The information contained here are property of DIGITAX Automotive Electronics Italy, and extremely con
fi
dential. Any disclosure, copying, distribution to third
party is strictly prohibited.
52
399
Time-Out keyboard locked
: this is the me a er which the keyboard gets unlocked (ac vated) automa cally if WD-commands are not received
anymore. As long as this me has not passed the keyboard remains locked (not ac ve).
This is valid for a me-out value of 1 or higher. A me-out value of 0 is a special case. In this case there is no me-out and the keyboard can
only be unlocked by means of an unlock-command (LM-command). See also paragraphs 2.1.2 (LM-command) and 2.1.22 (WD-command) of the
commtax2 manual. The me is given in seconds with an accuracy of 1 sec. The allowed value goes from 0 (min) to 255 (max).
0-255
400
Time out from trip start to accept forfait price.
0 - 65535
from Q 401 / Available for any possible so ware extension / to Q 402
403
Key bitmap enabled while the keyboard is blocked by overspeed
No / Yes
404
Tari
ff
number to which are des nated all sta s cal memories calculated by the current block
0-6
405
Min. distance (in meters) which allows the trip to be saved (if less, tripp will be not considered)
0-255
406
Speed to block the keyboard of the taximeter
: this is the speed above which the keyboard of the taximeter gets locked. As soon as the speed
becomes less than this threshold the keyboard gets unlocked again. Normally the value programmed here is a low speed like for example 10
Km/h. The speed is given in Km/h with an accuracy of 1 Km/h. The allowed value goes from 0 (min) to 255 (max). The value 0 is a special case.
It means: disabled.
0-255
407
Speed to block the coun ng of the tari
ff
: this is the speed above which the taximeter stops coun ng the tari
ff
. As soon as the speed becomes
less than this threshold the taximeter con nues coun ng the tari
ff
again. Normally the value programmed here is a high speed like for example
140 Km/h. The speed is given in Km/h with an accuracy of 1 Km/h. The allowed value goes from 0 (min) to 255 (max). The value 0 is a special
case. It means: disabled.
0-255
408
Block number if from Stopped back to Hired
: this is the number of the block that will be used when passing from Stopped back to Hired.
The allowed value goes from 0 (min) to 62 (max).
0 – 62
409
Block number if from Stopped to ForHire
: this is the number of the block that will be used when passing from Stopped to ForHire.
The allowed value goes from 0 (min) to 62 (max).
0 - 62
OTHER SETTINGS
410
Number of next block with key K1 delayed
: this is the number of the next tari
ff
-block to be used when key K1 is kept pressed for about a
second.
The allowed value goes from 0 (min) to 62 (max).
0 - 62
411
Distance for autotest
: this is the distance with which the vehicle is calibrated. The distance is given in metres with an accuracy of 1 metre.
The allowed value goes from 0 (min) to 9999 (max).
0 - 9999
metres
412
Sta s cal memories chosen to be print ed out (value 0= print all from 1 to 16)
1-65535
413
Sta s cal memories chosen to be print ed out (value 0= print all from 17 to 32)
1-65535
414
Sta s cal memories chosen to be print ed out (value 0= print all from 32 to 45)
1-8191
from Q 415
/ Available for any custom parameter /
to Q 423
424
Time to block the keys in stopped posi on
Possible Se ngs
from 1 to 127 : Seconds to block the Keyboard when the taximeter pass from Hired -> Stopped
+128 : At any key pressure show the word BLOC
+256 : During the Keys block the OP key is exclude (it will con nue to operate)
+512 : During the Keys block the K1 key is exclude (it will con nue to operate)
+1024 : During the Keys block the K2 key is exclude (it will con nue to operate)
+2048 : During the Keys block the K3 key is exclude (it will con nue to operate)
+4096 : During the Keys block the K4 key is exclude (it will con nue to operate)
+8192 : Special condi on. The me coun ng start from the beginning of the receipt prin ng, then the taximeter go to For-Hire and keep
freeze the amount on the display while d’ont expire the me programmed. Also is not possible start a new trip while d’expire the me
programmed.
+16384 : At the me expire the taximeter go automa cally to For Hire posi on.
0-65535
425
Tip Arround or increment
Possible Se ngs
0 = Disabled
1 ->255 = Cents to Arround the Fare with K1 in Stopped
+256->65535 = Amount/256 to increase the Tip with K2 in Stopped (Amount/256)x10) to increase the Tip with K3 in Stopped During the Tip
K4 Clear the Tip amount
0-65535
from Q 426
/ Available for any custom parameter /
to Q 429
Summary of Contents for M1 mdt
Page 1: ...Technical Manual InstallationandProgramming ver 1 16 12 2014...
Page 2: ......
Page 83: ......
