DigiTech AT Wizard M5 Manual Download

Page: 6 / 11

The App

The following explanation applies only to the Android App. The IOS App for
Apple is self-explanatory.

Attention, please always switch on the AT Wizard M5 first and then start the

app

Now start the app. First you will be asked if our app is allowed to activate
Bluetooth. Please confirm this with "YES" .Now please switch on the AT

Wizard M5. Press the button on the AT Wizard M5 for about 2 seconds. The
menu will appear on the screen. Please do not try to install the AT Wizard M5

or its Bluetooth connection manually via the Bluetooth Manager. Just start
the app and switch on the AT Wizard.

After starting, please activate the communication to the AT Wizard M5.
To do this, tap on the "Connect" slider, then your smartphone will search for

the AT Wizard and the display will change from "Disconnected" to
"Connected". After that, a value is shown on the "Angle" field. The

establishment of the connection to the AT Wizard M 5 can take up to 6
seconds depending on the smartphone.

After the connection has been established, you can read off the angle of the flap in degrees
in the Angle field.

Summary of Contents for AT Wizard M5












Search results

Summary of Contents for AT Wizard M5

Reviews:

Related manuals for AT Wizard M5

Brands by name

Popular brands

DigiTech AT Wizard M5, Manual

Search results

Summary of Contents for AT Wizard M5

Reviews:

Related manuals for AT Wizard M5

Brands by name

Popular brands