background image

WARRANTY

We at DigiTech

®

 are very proud of our products and back-up each one we sell with the following warranty: 

1.  Please register online at 

digitech.com

 within ten days of purchase to validate this warranty. This warranty is valid only in the 

United States.

2.  DigiTech warrants this product, when purchased new from an authorized U.S. DigiTech dealer and used solely within the U.S., 

to be free from defects in materials and workmanship under normal use and service. This warranty is valid to the original 
purchaser only and is non-transferable.

3.  DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, 

provided the product is returned to DigiTech WITH RETURN AUTHORIZATION, where all parts and labor will be covered up 
to a period of one year (this warranty is extended to a period of six years when the product has been properly registered 
through our website). A Return Authorization number may be obtained by contacting DigiTech. The company shall not be 
liable for any consequential damage as a result of the product’s use in any circuit or assembly.

4.  Proof-of-purchase is considered to be the responsibility of the consumer. A copy of the original purchase receipt must be 

provided for any warranty service.

5.  DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this product without 

incurring any obligation to install the same on products previously manufactured.

6.  The consumer forfeits the benefits of this warranty if the product’s main assembly is opened and tampered with by anyone 

other than a certified DigiTech technician or, if the product is used with AC voltages outside of the range suggested by the 
manufacturer.

7.  The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person 

to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be 
liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their 
control.

NOTE: The information contained in this manual is subject to change at any time without notification. Some information 
contained in this manual may also be inaccurate due to undocumented changes in the product since this version of the manual 
was completed. The information contained in this version of the owner’s manual supersedes all previous versions.

TECHNICAL SUPPORT & SERVICE 

If you require technical support, contact DigiTech Technical Support. Be prepared to accurately describe the problem. Know 
the serial number of your device – this is printed on a sticker attached to the chassis. If you have not already taken the time to 
register your product, please do so now at 

digitech.com

.

Before you return a product to the factory for service, we recommend you refer to this manual. Make sure you have correctly 
followed installation steps and operating procedures. For further technical assistance or service, please contact our Technical 
Support Department at (801) 566-8800 or visit 

digitech.com

. If you need to return a product to the factory for service, you MUST 

first contact Technical Support to obtain a Return Authorization Number. 

NO RETURNED PRODUCTS WILL BE ACCEPTED AT THE FACTORY WITHOUT A RETURN AUTHORIZATION NUMBER. 

Please refer to the Warranty information, which extends to the first end-user. After expiration of the warranty, a reasonable 
charge will be made for parts, labor, and packing if you choose to use the factory service facility. In all cases, you are responsible 
for transportation charges to the factory. If the product is still under warranty, DigiTech will pay the return shipping.

Use the original packing material if it is available. Mark the package with the name of the shipper and with these words in red: 
DELICATE INSTRUMENT, FRAGILE! Insure the package properly. Ship prepaid, not collect. Do not ship parcel post.

Summary of Contents for dirty robot













Reviews: