background image

©2002 Digitrax, Inc

www.digitrax.com

20

• Connect the equipment into an outlet on a circuit different form that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Note: Any modifications to the equipment not expressly approved by Digitrax
voids the user's authority to operate under and be in compliance with CFR 47
rules, as administered by the Federal Communication Commission. Digitrax
believes any conscientiously installed equipment following guidelines in this
manual would be unlikely to experience RFI problems. 

1155..00 

 

W

Waarrrraannttyy 

 

aanndd 

 

RReeppaaiirr 

 

IInnffoorrm

maattiioonn

Digitrax guarantees the BDL162 to be free from manufacturing defects for five
years from the date of purchase. These units are not user serviceable. If a
defect occurs, return the unit to Digitrax for service. Digitrax will repair or
replace BDL162s at our discretion at no charge to you for five years from pur-
chase date. This warranty excludes damage due to abuse, such as failure to
properly protect against input over current with a fuse or circuit breaker or
applying excessive input voltage to the unit. 

Digitrax will make non-warranty repairs needed because of physical damage or
electrical abuse at fair and reasonable rates. 

All warranties on Digitrax products are limited to refund of purchase price or
repair or replacement of Digitrax products at the sole discretion of Digitrax. 

In the event that Digitrax products are not installed or used in accordance with
the manufacturer's specifications, any and all warranties either expressed or
implied are void. Except to the extent expressly stated in this section, there are
no warranties, express or implied, including but not limited to any warranties
of merchantability or fitness for a particular purpose.

Digitrax, Inc. reserves the right to make changes in design and specifications
and/or to make additions or improvements in its products without imposing any
obligations upon itself to install these changes, additions or improvements on
products previously manufactured.

Summary of Contents for BDL162














Reviews: