INSTALLATION MANUAL
DIGIWAY PLUS
13
cdvi.com
cdvigroup.com
EN
Guided confi guration
Guided confi guration
The operator is supplied with a 4-button transmitter included. On completion of the mechanical fi xing and the electric connections, proceed
The operator is supplied with a 4-button transmitter included. On completion of the mechanical fi xing and the electric connections, proceed
with the memorization of the transmitter into the internal memory inside Digiway. This transmitter can then set-up of all parameters, without
with the memorization of the transmitter into the internal memory inside Digiway. This transmitter can then set-up of all parameters, without
accessing the 5 buttons
accessing the 5 buttons onboard
onboard..
The transmitter keys corresponds to the onboard push-button according to the next diagram:
The transmitter keys corresponds to the onboard push-button according to the next diagram:
The set-up of the operator can be divided into 5 steps:
The set-up of the operator can be divided into 5 steps:
•
•
STEP I
: INITIAL SETUP
STEP I
: INITIAL SETUP
( preliminary actions )
( preliminary actions )
•
•
STEP II
: CONFIGURATION
STEP II
: CONFIGURATION
( set-up of the basic operating mode )
( set-up of the basic operating mode )
•
•
STEP
STEP III : DOOR CALIBRATION
III : DOOR CALIBRATION
( automatic detection of the door characteristics )
( automatic detection of the door characteristics )
•
•
STEP
STEP IV : ADJUSTMENTS
IV : ADJUSTMENTS
( further adjustments and personalization )
( further adjustments and personalization )
•
•
STEP
STEP V : SPECIAL PARAMETERS
V : SPECIAL PARAMETERS
(
( set-up of the
set-up of the advanced parameters )
advanced parameters )
Press the OK button of the keyboard
Press the OK button of the keyboard for
for
4 sec
4 sec
until the display enters the main menu ;
until the display enters the main menu ;
Select the language by scolling the possibile choices with the UP and DOWN buttons
Select the language by scolling the possibile choices with the UP and DOWN buttons
Press OK to confi rm: the display shows the message OK and then displays all messages in the new language;
Press OK to confi rm: the display shows the message OK and then displays all messages in the new language;
Exit from the menu with the button ESC.
Exit from the menu with the button ESC.
Scroll through the main menu, select
Scroll through the main menu, select
TX MANAGEMENT
TX MANAGEMENT
submenu and press OK
submenu and press OK
Select the option
Select the option
ADD TX
ADD TX
and press
and press
OK
OK
Press the transmitter key A (top-left button): the display will show the S/N, confi rming the memorization
Press the transmitter key A (top-left button): the display will show the S/N, confi rming the memorization
Exit from the menu by pressing the ESC button.
Exit from the menu by pressing the ESC button.
Exit from the main menu selecting EXIT MENU.
Exit from the main menu selecting EXIT MENU.
From this time on the remote control is enabled to access the main menu. Enter simply by pressing simultaneously keys
From this time on the remote control is enabled to access the main menu. Enter simply by pressing simultaneously keys
C + D
C + D ..
NOTE : ONLY THE FIRST TRANSMITTER MEMORIZED CAN ACCESS THE MAIN MENU! All the next added transmitters can only
NOTE : ONLY THE FIRST TRANSMITTER MEMORIZED CAN ACCESS THE MAIN MENU! All the next added transmitters can only
open the door!
open the door!
The key OK of the transmitter can do multiple functions: OK if you are in the menu, START / STOP in normal operating.
The key OK of the transmitter can do multiple functions: OK if you are in the menu, START / STOP in normal operating.
ESC
ESC
DOWN
DOWN
UP
UP
UP
UP
DOWN
DOWN
ESC
ESC
STEP I: INITIAL SETUP
2
1
3
4
5
6
7
8
9
