8 www.dimplex.com
standoffs and gently lift the board off.
9. Properly orient and insert the new board and connect
all of the wiring.
!
NOTE:
If any tie wraps were removed, replace and en-
sure that none of the wires are pinched during reassembly.
10. Reassemble in the reverse order as above.
AC/DC ADAPTER REPLACEMENT
Tools Required:
Phillips Head Screwdriver
Flat Head Screwdriver
CAUTION:
If unit was operating prior to servicing allow
at least 10 minutes for lights, heating elements and top
panel to cool off to avoid accidental burning of skin.
WARNING:
Disconnect power before attempting any
maintenance to reduce the risk of electric shock or damage
to persons.
1. Unplug the unit from power outlet.
2.
Remove the firebox from the back of the mantel by
removing the retaining screws which secure the firebox
brackets to the mantel.
3. Remove the four screws along the back of the unit, the
two on either side along the top edge. (Figure 3)
4.
Lay the Compact Fireplace on its back.
5.
Remove the six screws on the top surface. (Figure 3)
6.
Gently open the top panel, laying it on the work sur
-
face so that all of the components can easily be seen.
(Figure 4)
!
NOTE:
The wires are grouped together with tie wraps,
which may need to cut to fully open the top panel.
7. Locate the adapter and disconnect the wiring connec-
tions noting their original locations.
8. There is one connection located on the display/control
board that requires the board to be removed. This can
be done by removing the two screws on the right hand
side of the unit, reaching between the partially reflective
panel and the back of the unit, to remove the display/
control board to remove the connection and replace it
with the new one.
9. Reinstall the display/control board.
10. Remove the adapter from the top panel by removing
the four screws securing it to the top panel.
11. Properly orient and insert the new adapter and connect
all of the wiring.
!
NOTE:
If any tie wraps were removed, replace and en-
sure that none of the wires are pinched during reassembly.
12. Reassemble in the reverse order as above.
HEATER ASSEMBLY REPLACEMENT
Tools Required:
Phillips Head Screwdriver
Flat Head Screwdriver
CAUTION:
If unit was operating prior to servicing allow
at least 10 minutes for lights, heating elements and top
panel to cool off to avoid accidental burning of skin.
WARNING:
Disconnect power before attempting any
maintenance to reduce the risk of electric shock or damage
to persons.
1. Unplug the unit from power outlet.
2.
Remove the firebox from the back of the mantel by
removing the retaining screws which secure the firebox
brackets to the mantel.
3. Remove the four screws along the back of the unit, the
two on either side along the top edge. (Figure 3)
4.
Lay the Compact Fireplace on its back.
5.
Remove the six screws on the top surface. (Figure 3)
6.
Gently open the top panel, laying it on the work sur
-
face so that all of the components can easily be seen.
(Figure 4)
!
NOTE:
The wires are grouped together with tie wraps,
which may need to cut to fully open the top panel.
7. Locate the heater assembly and disconnect the wiring
connections noting their original locations.
!
NOTE:
A flat head screwdriver can be used to gently
pry between the end of the connector and the switch to
release the wires.
8. Remove the 4 screws that secure the top panel to the
heater assembly
9. Properly orient and install the new assembly and con-
nect all of the wiring.
WARNING:
Ensure wires do not come in contact with
moving parts by securing wires in wiring tie wraps.
10. Reassemble in the reverse order as above.
POWER CORD REPLACEMENT
Tools Required:
Phillips Head Screwdriver
CAUTION:
If unit was operating prior to servicing allow
at least 10 minutes for lights, heating elements and top
panel to cool off to avoid accidental burning of skin.
WARNING:
Disconnect power before attempting any
maintenance to reduce the risk of electric shock or damage
to persons.
1. Unplug the unit from power outlet.
2.
Remove the firebox from the back of the mantel by
removing the retaining screws which secure the firebox
brackets to the mantel.
3. Remove the four screws along the back of the unit, the
two on either side along the top edge. (Figure 3)
4.
Lay the Compact Fireplace on its back.
5.
Remove the six screws on the top surface. (Figure 3)
6.
Gently open the top panel, laying it on the work sur
-
