background image

4             www.dimplex.com

Ember Bed

Assembly

Front Edge

Rear Tab

Back Ledge

Mirror

MAINTENANCE

Light Bulb Replacement (Mod 0-A Only)

Allow at least five (5) minutes for light bulbs to cool before 

touching bulbs to avoid accidental burning of skin.
Light bulbs need to be replaced when you notice a dark 

section of the flame or when the clarity and detail of the 

log ember bed exterior disappears.  There are two 2 bulbs 

under the log set, which generate the flames and embers.

Light Bulb Requirements

Quantity of two 2 clear chandelier or candelabra bulbs with 

an E-12 (small) socket base, 60 Watt rating.  Example: GE 

60BC or Philips 60 CTC.

Do not exceed 60 Watts per bulb .
Helpful Hints

It is a good idea to replace both light bulbs at one time 

if they are close to the end of their rated life.  Group 

replacement will reduce the number of times you need to 

open the unit to replace light bulbs.  Care must be taken 

when removing the log set.  

To Access The Lower Light Bulb Area: 

(Figure 3)

1.  Remove front glass assembly.
2.  Pull the front edge of the plastic Ember Bed, plastic 

grate or Media Tray (depending on Model) up and 

forward until the rear tab releases from the ledge 

located at the bottom of the partially reflective glass.

!

IMPORTANT:  

Only handle the log set by the ember bed.

!

NOTE:  

Log set fits tightly into firebox, some force may 

be necessary to remove.
3.  Set Log Set/ Media Tray in front of fireplace.
4.  Disconnect flicker from motor (see Figure 3).
5.  Unscrew bulbs counter clockwise.
6.  Insert new bulbs.
7.  Reconnect flicker to motor.
8.  Replace the log set by inserting the front edge of the 

log set and push down on the rear edge of the ember 

bed until it snaps into place (Figure 4).

!

 NOTE:  

Ensure the log set is installed tightly under the 

back ledge to prevent light leakage.
9.  Replace glass assembly.

Glass Cleaning

The front glass is cleaned in the factory during the 

assembly operation.  During shipment, installation, 

handling, etc., the front glass may collect dust particles, 

these can be removed by dusting lightly with a clean dry 

cloth.
To remove fingerprints or other marks, the glass can be 

cleaned with a damp cloth.  The glass should be completely 

dried with a lint free cloth to prevent water spots.  To 

prevent scratching, do not use abrasive cleaners or spray 

liquids on the glass surface.

Fireplace Surface Cleaning

To remove fingerprints or other marks, the exterior finish 

can be cleaned with a damp cloth with a mild detergent.  

The surface should be completely dried with a lint free cloth 

to prevent water spots

 .  

Figure 3

Flicker

Figure 4

Side Section

Summary of Contents for BF9000



















Reviews: