background image

10  

www.dimplex.com

  

Operation

  Set the 3 position manual 

control to the 

Remote

 position 

(right position).

  Press and hold the 

initialization button on the unit.

  While holding the initialization 

button, press the Flame/Heat on/
oFF   button on the remote 

control transmitter.  

  Release the initialization 

button on the unit.

⑦ 

Press the Flame/Heat on/off 

button   to turn the Flame/Heat 

function on.

Frequency Interference

If the fireplace does not respond 

properly to the remote control, 

the remote operating frequency 

may have to be reset. The 

remote control can send another 

frequency code to the circuit 

board to eliminate interference.

  Simultaneously press the 

Temperature Down

” button and 

the “

Flame Speed Down

” button 

on the remote control.

  “

COD

” will appear in place of 

the sleep timer digits.

  Release the “

Temperature 

Down

” button and the “

Flame 

Speed Down

” button.

  Press the initialization button 

on the unit.

  Press the   button on the 

remote.
Your remote will now have a  

different frequency 

communicating with the fireplace.

Summary of Contents for DCF44GS




















Reviews: