background image

 

13

Figure 6

Flicker

Rod

replace light bulbs.  Care must be 

taken when removing the log set.  

To Access The Lower Light 

Bulb Area: 

(Figure 6)

 

CAUTION: 

Allow at least 5 

minutes for light bulbs to cool 

before touching bulbs to avoid ac-

cidental burning of skin.
1.  Remove front glass assembly.
2.  Pull the back edge of the 

plastic ember bed forward 

until the rear tab releases 

from the ledge located at the 

bottom of the partially reflec-

tive glass.

!

IMPORTANT:  

Only handle the 

log set by the ember bed.

!

NOTE:  

Log set fits tightly into 

firebox, some force may be nec-

essary to remove.
3.  Set log set in front of fire-

place.

Figure 7

Side Section

Front

Edge

Log 

Ember 

Bed

Back

Ledge

Rear

Tab

  Maintenance

4.  Disconnect the flicker rod 

from the motor (see Figure 6).

5.  Unscrew bulbs counter clock-

wise.

6.  Insert new bulbs.
7.  Reconnect the flicker rod to 

motor.

8.  Replace the log set by insert-

ing the front edge of the log 

set and push down on the 

rear edge of the ember bed 

until it snaps into place (Fig-

ure 7).

!

 NOTE:  

Ensure the log set is 

installed tightly under the back 

ledge to prevent light leakage.
9.  Replace glass assembly.

Glass Cleaning

The front glass is cleaned in the 

factory during the assembly op-

eration.  During shipment, instal-

lation, handling, etc., the front 

Summary of Contents for DF2426



















Reviews: