background image

IMPORTANT INSTRUCTIONS

PLEASE RETAIN THIS USER’S GUIDE FOR FUTURE REFERENCE

When using electrical appliances, basic precautions should always be
followed to reduce the risk of fire, electric shock, and injury to persons,
including the following:

1. Read all instructions before using this fireplace.
2. This fireplace is hot when in use.  To avoid burns, do not let

bare skin touch hot surfaces.  The trim around the heater outlet
becomes hot during heater operation.  Keep combustible
materials, such as furniture, pillows, bedding, papers, clothes,
and curtains at least 3 feet (0.9m) from the front of the unit.

3. Extreme caution is necessary when any heater is used by or

near children or invalids and whenever the fireplace is left
operating and unattended.

4. Do not operate any fireplace if the heater has malfunctioned, or

if the fireplace has been dropped or damaged in any manner.

5. Do not use outdoors
6. This fireplace is not intended for use in bathrooms, laundry

areas and similar indoor locations.

7. Do not insert or allow foreign objects to enter any ventilation or

exhaust opening as this may cause an electric shock or fire, or
damage to the heater.

8. To prevent a possible fire, do not block air intake or exhaust in

any manner.

9. All electrical heaters have hot and arching or sparking parts

inside.  Do not use in areas where gasoline, paint, or flammable
liquids are used or stored or where the unit will be exposed to
flammable vapors.

10. Do not modify this fireplace.  Use it only as described in this

manual.  Any other use not recommended by the manufacturer
may cause fire, electric shock or injury to persons.

11. Do not burn wood or other materials in this fireplace.
12. Do not strike fireplace glass.
13. Always use a certified electrician for installation.
14. Disconnect all power coming to fireplace at main service panel

before performing any cleaning, or maintenance.

15. When transporting or storing the fireplace, keep in a dry place,

free from excessive vibration and store as to avoid damage.

CAUTION:

  Procedures and techniques which, if not carefully followed,

will result in damage to the equipment.

WARNING:

  Procedures and techniques which, if not carefully followed,

will expose the user to the risk of fire, serious injury, illness or death.

To access the light bulb area:

1. Open steel curtain (remove glass doors if applicable).
2. Remove two screws on log grate and remove.
3. Pull rear edge of ember bed up and forward by grasping ember

bed by the sides (handle the logset only by the emberbed and
not the logs) and pulling solidly until the rear tab pops out from
under the back ledge, then lift out.

4. Pull the left side of the rotating element up and out of the

bracket.  Swing the rotating element out of the way just enough to
access the light bulbs being carefull not to damage the mounting
spring.

5. Examine the bulbs to determine which bulbs require replacement.
6. Unscrew bulbs counter clockwise.
7. Insert new bulbs.
8. Install the rotating element back into the mounting bracket

ensuring that the rubber grommet is fully seated.

9. Replace the log by inserting front edge and pushing the back down

until rear tab snaps under back ledge and the logs are
resting against mirror.

10.Replace log grate using two screws previously removed.

6

1

Pull up on
Rotating element

Log grate

Light bulbs

Remove screws

Logset

Summary of Contents for Indoor Electric Fireplace







Reviews: