Dimplex LVA191, User Manual

Use the wall plate as a template to mark the hole positions
for drilling - see 

Fig.2

.  Drill and fix the wall plate in position

with one screw initially to check the plate is level before
marking and drilling the remaining holes.
Ensure the wall plate is fitted the correct way up i.e. the side
hooks are pointed upwards. - see 

Fig.3

.

The appliance can then be hung on the wall plate by aligning
the slots on the chassis with the side hooks on the wall
plate.

Check to ensure that the bottom hooks have also engaged
in their respective slots.

The corner hinges on the wall plate may be used to secure
the appliance against inadvertent dislodgement. Simply
rotate the the hinges upwards to a position above the chassis
(see 

Fig.2

 and 

Fig.3

). They can then be screw fixed using the

screws removed earlier (see 

Fig.4

, detail 

‘X’, ‘1’

).

NOTE: The appliance should be hard wired to a fused
switched spur located behind the glass panel so as to be
hidden from view (see  

Fig. 1, ‘b’

). The programme compact

flash memory card is factory fitted and protected by a screw
fixed security cover, ( see 

Fig.4 ‘a’

) In normal use access to

the card is not a requirement.

Please consult a qualified electrician for appropriate wiring
Plug in the IEC connector from the hard wiring outlet to the
IEC fused (SSC 10A 250V) socket on the appliance (see

Fig.1

, detail 

A,1

).

The illuminated power ‘On’ switch (see 

Fig.5

 detail 

‘Z’, 1

)

must first be switched 

‘ON’

 to operate the appliance.

One of the scenes will automatically show when the power

‘ON’

 switch is operated.

Scene selection and sound control can now be acheived
manually or by remote control, see instructions below.

Note: The user may notice a slight frame freeze lasting less
than 0.5 seconds after a scene has run for approximately 5
minutes. This is normal and should not be a cause for
concern.

Twin fan heaters positioned one left, one right behind the
glass can be operated manually by switch(see 

Fig.5

 detail ‘

Z’, 2

) or by the remote control. Fan operation is indicated by a

red light, which will remain lit while the fans are in use, (see

Fig.1

 detail

 B, 1

). Each fan heater has an individual element

switch (see 

Fig.1

 detail 

C

)

this provides for cold blow operation

if heat is not required.

 (LVA191 Only)

 .

Manual Control Operation: - LVA191 - LVA191NH

The manual controls for the screen are located at the top of
the appliance behind the glass screen (see

 Fig.4, 

detail 

‘Y’

).

The membrane switch functions are as described below;

              Standby Switch 

‘On’

 / 

‘Off’

 a red light indicates

standby mode. (See 

Fig.1

 detail 

B,2

)

Sound Volume ‘Up’

Sound Volume ‘Down’

Scene Selection ‘Up’

Scene Selection ‘Down’

The manual switch for the fan heaters, (see 

Fig.5

 detail 

‘Z’

,

2

). Each fan heater has an element switch to provide the

option of hot or cold blow, (see 

Fig.1

. detail 

C

). 

(LVA191 Only)

The appliance Illuminated Power switch (see 

Fig.5

 detail 

‘Z’

,

1

) may be used to switch the appliance 

‘OFF’

 when it is not

required, say overnight or for long periods, to avoid energy
wastage.

Remote Control Operation: - LVA191 - LVA191NH

The remote control may be operated once the appliance is
switched 

‘ON’

 (see 

Fig.5, 

detail

 ‘Z’, 1

).

Aim the remote control at the screen (I.R. sensor is indicated
in 

Fig.1

 detail 

B, 3

) select any one of the eight scenes on your

remote control (see 

Fig.7

)

Each scene has it’s own particular sound effect which may
be activated and adjusted up or down by pressing the  volume

control buttons (

 and 

) until the level required is

reached.

The fan heaters may be switched 

‘ON’

 and 

‘OFF’

 by pressing

the buttons 

 or 

. A red light indicates the fans are in

operation and will remain lit while the fans are 

‘ON’

 (see

Fig.1

 detail

 B, 1

).  

(LVA191 Only)

The button functions are identified as described below;

‘Coal’ Fire scene

‘Log’ Fire scene

‘Embers’ Fire scene

‘Spring’ scene

‘Summer’ scene

‘Autumn’ scene

‘Winter’ scene

‘Aquarium’ scene

 Fan Heater ‘ON / ‘OFF’. (Hot or Cold blow option

 is by manual selection

 LVA191 only

)

Note: When the standby switch is operated it will switch off
the fan heaters if they happen to be 

‘ON’

 and they will not

come back 

‘ON’

 automatically when the appliance is switched

out of the standby mode. They will need to be deliberately
switched back 

‘ON’

, if required, either manually or by remote

control.

A red light will indicate when the appliance is in standby
mode. 

(See 

Fig.1

 detail 

B,2

)

On the 

LVA191

 the fan heaters can be operated when the

scenes are in standby, if desired, and in which case there
will be two red lights displayed, one indicating the standby
mode and the other fan heaters 

‘ON’

. 

(See 

Fig.1

 detail 

B,1 &

2

)

Remote Control Assembly.

Note: The remote control is packed separately in the carton.

1.

Slide open the battery cover on the back of the remote
transmitter.

2.

Install the AAA batteries into the remote control (see

Fig. 6

).

3.

Replace battery cover.