Important Safety Advice:
When using electrical appliances, Basic precautions
should always be followed to reduce the risk of fire,
electrical shock, and injury to persons, including the
following:
If the appliance is damaged, check with the supplier
before installation and operation.
Do not use outdoors.
Do not use in the immediate surroundings of a bath,
shower or swimming pool.
Do not locate the heater immediately below a fixed
socket outlet or connection box.
Do not cover the heater. Do not place material or
garments on the heater, or obstruct the air circulation
around the heater, for instance by curtains or furniture,
as this could cause overheating and a fire risk.
This appliance is not intended for use by children or
other persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them
from using it safely. Children should be supervised to
ensure that they do not play with the appliance.
Do not use this heater in series with a thermal control,
a program controller, a timer or any other device that
switches on the heat automatically, since a fire risk
exists when the heater is accidentally covered or
displaced.
Ensure that furniture, curtains or other combustible
material are positioned no closer than 1 metre from the
heater.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
Although this heater complies with safety standards,
we do not recommend its use on deep pile carpets or
on long hair type of rugs.
The appliance must be positioned so that the plug is
accessible.
If the supply cord is damaged it must be replaced by
the manufacturer or service agent or a similarly qualified
person in order to avoid a hazard.
Keep the supply cord away from the front of the heater.
General
Unpack the heater carefully and retain the packaging for possible
future use, in the event of moving or returning the fire to your
supplier.
The fire incorporates a flame effect, which can be used with or
without heating, so that the comforting effect may be enjoyed at
any time of the year. Using the flame effect on its own only
requires little electricity.
These models are designed to be free standing and are normally
positioned against a wall.
Before connecting the heater
check that the supply voltage is
the same as that stated on the heater.
Please note: Used in an environment where background noise
is very low, it may be possible to hear a sound which is related
to the operation of the flame effect. This is normal and should
not be a cause for concern.
Mozart Electric Fire Suite - Model: MZT20
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the voltage
marked on the heater must correspond to the supply voltage.
Before switching on, please read the safety warnings and
operating instructions.
Controls
-
see
Fig. 2
Three switches provide a choice of heat settings. A switch is in
the ON position when the side with the markings on (i.e.
I
,
I
, or
II
) is pushed in.
Switch 1 (I)
Controls the electricity supply to the
heater and flame effect.
Note: This switch must be in the ON (I) position for heater
to operate with or without heat.
Switch 2 (I)
Provides 1kW heat output
Switch 3 (II)
Provides 2kW output with switch 2
Thermal Safety Cut-out
A thermal safety cut-out is incorporated in the heater to prevent
damage due to overheating. This can happen if the heat outlet
was restricted in any way. The heater will switch on once the
obstruction has been removed and the heater has cooled. If the
cut-out continues to operate intermittently, the heater should be
switched off and a service agent contacted.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.
Lamp replacement
- see
Fig.’s 3
,
4
and
5
The lamps are located behind the back panel. To gain access to
the lamps, the screws indicated in
Fig. 3
(4 screws) which secure
the back panel, must be removed.
Remove and slide out panel as indicated on
Fig. 4
.
Remove the defective lamp by unscrewing it as shown in
Fig. 5
.
Replace with a 60W E14 SES Clear Candle lamp. Take care
not to over-tighten the lamp.
Refit the back panel and secure with the screws.
Painting
The fire surround is finished with a multi-coat paint which provides
a robust, durable finish.
If you wish to paint the surround in another colour , to ensure
good adhesion, you should sand the surround down first, and
then use one of the specialist MDF paints that are now
commercially available.
To remove the fire prior to painting, please remove the screws
at the back (8 screws) and slide out the electric fire to the front
as shown in
Fig. 3
.
