background image

NOTE 

To turn the ambient light sensor OFF repeat steps 1 to 3 and then press the down button. 

 

SLOW START/FADING EMBERS 

If the slow start function is being used at start up then the fading embers function will 
automatically be programmed at shut down. 
1.  Press the ENTER button until the middle display       flashes. 
2.  Use the direction buttons on the hand held remote to move the cursor to      and press 

ENTER. 

3.  Press the left or right button to select 1, 5, or 10 minutes. 

NOTE 

When the timer is set to 1, 5, or 10 minutes it determines the length of time over which the 
embers will fade upon turning the unit OFF. 

NOTE

 

The slow start function timer is automatically programmed for 1 minute.  This timer setting 
cannot be changed. 
4.  Press the up button to turn the slow start/fading embers function ON. 
5.  Press ENTER to return to the main menu. 
6.  Press the flame on/off      button to activate slow start. 

NOTE

 

When turning the unit OFF and the slow start/fading ember function is ON, the slow        
start/fading ember      indicator will flash. 

 

OCCUPANCY SENSOR

 

The occupancy sensor function can be programmed to turn the fireplace ON when it 
detects movement.  The occupancy sensor is programmed to turn the fireplace OFF when 
it doesn’t detect movement in 5, 10, or 20 minutes.  The occupancy sensor has a range of 
10 feet. 
1.  Press the ENTER button until the middle display       flashes. 
2.  Use the direction buttons on the hand held remote to move the cursor to      and press 

ENTER. 

3.  Press the left or right button to 5, 10, 0r 20 minutes. 
4.  Press the up button to turn the occupancy sensor ON. 
5.  Press ENTER to return to the main menu. 

NOTE 

To turn the occupancy sensor OFF repeat steps 1 to 3 and then press the down button. 

 

CHILD LOCK 

1.  Press the ENTER button until the middle display       flashes. 
2.  Use the direction buttons on the hand held remote to move the cursor to    and press 

ENTER. 

3.  Press and hold the up button for 4 – 5 seconds.  The     will flash when the child lock 

function has been turned ON. 

4.  To turn the child proof function OFF, hold the down arrow key for 4 – 5 seconds. 

 

PURIFIRE 

1.  Press the ENTER button until the middle display       flashes. 
2.  Press the ENTER button on the       purifire function. 
3.  Press the left of right button to select LOW or HIGH. 
4.  Press the up button to turn the purifire ON. 
5.  Press ENTER to return to the main menu. 

NOTE

 

To turn the purifire OFF repeat steps 1 to 3 and then press the down button. 

Summary of Contents for MULTIFIRE DF3215

Page 1: ...ee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and ...

Page 2: ... repeatedly will increase the sleep timer by 30 minute increments 3 Press the flame button and or the heater button to turn the unit ON 4 The fireplace will automatically turn OFF when the sleep timer reaches 0 minutes 5 The sleep timer can be reset by pressing the sleep timer button repeatedly until the sleep timer display disappears and the room temperature display is shown SET CLOCK 1 Press the...

Page 3: ...ss the ENTER button until the middle display flashes 3 Use the direction buttons on the hand held remote to move the cursor to and press ENTER 4 Repeatedly press the left or right arrow keys to change the flame speed NOTE The bar graph located on the top of the screen displays the speed range of the flame motor 5 Press ENTER to return to the main menu LIGHT DIMMER 1 Press the flame button to turn ...

Page 4: ...n the fireplace ON when it detects movement The occupancy sensor is programmed to turn the fireplace OFF when it doesn t detect movement in 5 10 or 20 minutes The occupancy sensor has a range of 10 feet 1 Press the ENTER button until the middle display flashes 2 Use the direction buttons on the hand held remote to move the cursor to and press ENTER 3 Press the left or right button to 5 10 0r 20 mi...

Reviews: