Important Safety Advice
When using electrical appliances, basic precautions
should be followed to reduce the risk of fire, electric
shock, and injury to persons, including the following:
If the appliance is damaged, check immediately with the
supplier before installation and operation.
Do not use this heater in the immediate surroundings
of a bath, shower or swimming pool
.
Do not use outdoors.
This heater must not be located immediately above or
below a fixed socket outlet or connection box.
Do not cover or obstruct in any way the heat outlet grille
located underneath the heater. Overheating will result if
the heater is accidentally covered.
In the event of a fault unplug the heater.
Unplug the heater when not required for long periods.
The supply cord must be placed on the right hand side
of the heater away from the heat outlet underneath the
heater.
Although this heater complies with safety standards, we
do not recommend its use on deep pile carpets or on
long hair type of rugs.
This appliance is not intended for use by children or other
persons without assistance or supervision if their
physical, sensory or mental capabilities prevent them
from using it safely. Children should be supervised to
ensure that they do not play with the appliance.
The appliance must be positioned so that the plug is
accessible.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or similarly qualified
person in order to avoid a hazard.
Caution: In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must not
be supplied through an external switching device, such
as a timer, or connected to a circuit that is regularly
switched on and off by the utility.
General
Unpack the heater carefully and retain the packaging for
possible future use, in the event of moving or returning the fire
to your supplier.
The fire incorporates a flame effect, which can be used with or
without heating, so that the comforting effect may be enjoyed at
any time of the year. Using the flame effect on its own only
requires little electricity.
Before connecting the heater
check that the supply voltage is
the same as that stated on the heater.
Please note: Used in an environment where background noise
is very low, it may be possible to hear a sound which is related
to the operation of the flame effect. This is normal and should
not be a cause for concern.
Electrical connection
WARNING – THIS APPLIANCE MUST BE EARTHED
This heater must be used on an AC ~ supply only and the
voltage marked on the heater must correspond to the supply
voltage.
Before switching on, please read the safety warnings and
operating instructions.
Nardini NDN20 Wall Fire
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
Wall fixing
- see
Fig. 1
The appliance should be securely fixed to the wall using the
wall plugs and screws supplied for block walls.
Note – for studded walls special fasteners are required, see
diagram for recommended position of fixing screws.
Recessed Installation
Please note that this appliance can also be wall-mounted so
that it is recessed. This can be installed in a large fireplace
opening or a purpose built wall. See Table 1 for size of recess
required and hole fixing dimensions.
This fireplace insert does NOT require venting.
In order to ensure its future safety in use, it is essential that this
fire is securely fixed to the wall.
IT IS IMPORTANT THAT THE FIXING DEVICE CHOSEN IS
APPROPRIATE TO THE WALL MATERIAL TO WHICH THE FIRE
IS BEING FIXED. SOME MODERN INTERNAL BUILDING
MATERIALS ARE VERY LOW DENSITY BLOCK AND REQUIRE
SPECIALIZED FIXING DEVICES TO PROVIDE A SAFE, SECURE
INSTALLATION.
The installation of this fire should be carried out by a competent
person. If in doubt please consult your local builder. This section
provides step by step instructions for selecting a location and
preparing the site to install the fireplace into the following:
Existing Fireplace
1.
Make sure that the fire is located on a flat surface.
2.
Seal all draughts and vents to prevent chimney debris from
falling onto the Fireplace Insert. Do not install into an existing
fireplace that is prone to dampness.
3.
Remove the front/trim by following the steps as outlined
above.
4
. Locate the 4 fixing holes, position the fire accordingly, and
firmly fix the appliance to the wall using the appropriate
screws
5
. Replace the front/trim.
New Support Structure Construction
When planning where to position your purpose built support
structure the following steps must be observed:
1.
Place the fire in the desired location to see how it will look in
the room.
2.
Mark the desired location for the new support structure in the
room and store the fire in a safe, dry and dust free location.
3.
Using timber studs to support the fire, devise and construct
a suitable means of supporting the product within the wall
partition and provide electrical power for the fire to be HARD
wired. For recommended sizes of height, width and depth of
opening for recess and hole fixing dimensions for each
model
4.
Remove the front/trim by following the steps as outlined
above.
5.
Locate the 4 fixing holes, position the fire accordingly, and
firmly fix using the appropriate screws.
6
. Replace the front/trim.
NOTE: The appliance should be HARD wired to an electrical
power outlet when placed in a recessed installation. Please
consult a qualified electrician for appropriate wiring
requirements.
