Operating the Product
This section describes how to activate your fire using either the manual controls or remote control. Inert the mains
plug to the socket outlet (ensure that the supply voltage matches the voltage marked on the appliance).
MANUAL CONTROLS
The manual controls are located beneath the metal bed -
see Fig. 11
for Manual Control lay out.
Switch ‘A’:- Controls the electricity supply from the power supply unit to the Fire.
Note: This switch must be in the ‘ON’
( I )
position for the Fire to operate.
BLUE TOOTH (BT) RECEIVER
Button ‘B’:- Press
once to turn on the flame effect. The LED’s light up - it will take a further 45 seconds before the
flame effect starts.
(Button ‘C’ is used to pair the remote control - see Blue Tooth Remote Control section below)
Press
to put fire in to standby mode. This will be indicated by the LED’s switched off.
Button ‘D’and ‘E’:- Control the intensity of the flame effect.
Press button ‘D’ to decrease the flame height.
Press button ‘E’ to increase the flame height.
When flame height reaches max. or min. the LED’s will blink once.
Give the flame generator a couple of seconds to react to changes you may make.
The appliance will use less water if the flame effect is set to a lower level.
The Blue Tooth receiver can be removed from its location and placed outside the product if preferred. To do this,
remove the metal bed -
see Fig. 3
, remove the Air filter - Unclip the BT receiver and feed it out through the air filter
inlet hole -
see Fig. 12
. Unwind the cable from underneath and fit the BT receiver where desirable (cable length from
inlet hole is 120cm). Replace the filter and the metal bed.
BLUE TOOTH (BT) REMOTE CONTROL
The remote control is supplied with 2xAAA batteries. Remove the battery cover
from the underside of the remote control
-
see Fig. 13
and after removing the batteries from the plastic wrapping fit them into place. Replace the battery cover.
The remote control has wireless technology and is required to be paired to the receiver. This is done by pressing the
button (C) on the BT receiver. The LED’s will start to blink on and off. This is to let you know that the appliance is ready
to connect to the remote control. Press the button (B) on the remote control. The appliance will switch off. Now the
remote control is paired to the appliance.
The operation of the remote control is the same as described in ‘Receiver Controls’.
There are 3 buttons on the remote control -
see Fig. 14
. To operate correctly the remote must be pointed towards the
product. The remote control functions operate in the same way as the manual buttons ‘B’, ‘D’ and ‘E’.
Standby (B)
Flame down (D)
Flame up (E)
Maintenance
GENERAL TIPS
Only use decalcified/filtered tap water in this appliance.
Always ensure that the appliance is sitting on a level surface.
If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and water tank.
Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.
The appliance should never be operated if the LED’s are not working.
FILLING THE WATER TANK
When the water tank needs refilling, the LED’s, flame/smoke effect shuts off. (To indicate when tank needs refilling,
the LED’s blink twice, approximately 15 minutes before the flame/smoke shuts off)
1. Lift out the metal bed and place carefully on the table/worktop -
see Fig. 3
.
2. Remove the water tank by lifting upwards and outwards -
see Fig. 6.
3. Place the water tank in sink and remove cap, anti-clockwise to open -
see Fig. 9
.
4. Fill tank with
decalcified/filtered water only
. This is necessary to prolong the life of the flame and smoke
producing unit.
The water should be filtered through a conventional domestic water filter unit and the filter should be replaced
regularly.
5. Screw the cap back on (clockwise),
do not over tighten
.
3
