Dimplex SF3202 Service Manual Download

Page: 2 / 21

Contents

OPERATION ............................................................................................................................. 2

REMOTE CONTROL OPERATION ....................................................................................... 3

REPLACEMENT PARTS ........................................................................................................... 7

WIRING DIAGRAM ................................................................................................................... 8

LOWER BULB REPLACEMENT ............................................................................................... 9

UPPER BULB REPLACEMENT .............................................................................................. 10

TO REPLACE LED/SWITCH HARNESS ................................................................................. 11

TO REPLACE FLAME SPEED CONTROL ............................................................................. 12

TO REPLACE FLAME MOTOR/FLAME ROD ......................................................................... 13

TO REPLACE HEATER ON/OFF SWITCH ............................................................................. 14

TO REPLACE HEATER ASSEMBLY ...................................................................................... 15

TO REPLACE THE CIRCUIT BOARD..................................................................................... 16

TO REPLACE THE POWER CORD ........................................................................................ 17

TROUBLESHOOTING GUIDE ................................................................................................ 18

GENERAL ............................................................................................................................ 18

APPEARANCE .................................................................................................................... 18

HEATER .............................................................................................................................. 19

NOISE .................................................................................................................................. 20

Summary of Contents for SF3202






















Search results

Summary of Contents for SF3202

Reviews:

Related manuals for SF3202

Brands by name

Popular brands

Dimplex SF3202, Service Manual

Search results

Summary of Contents for SF3202

Reviews:

Related manuals for SF3202

Brands by name

Popular brands