Manual Operation
Note:
The Standby Switch (see ‘a’ in
Fig. 5
) must be first turned
on to operate either the manual or the remote controls. The red
indicator mark on the switch will be visible wh
en it is turned on.
Setting
Operation
Indication
Flame effect
Press the ‘
I
’ button once
Left Neon
Flame effect & 750W heat setting
Press the ‘
I
’ button again
Left & Middle Neon
Flame effect & 1500W heat setting
Press the ‘
I
’ button again
All 3 neon’s
To turn off any of the settings press the ‘
O
’ button once.
To increase or decrease the brightness of the fuel effect use the
buttons ‘
’ as shown in
Fig. 5
.
Initializing the Remote Control
Note: The remote control is packed separately in the carton.
1.
Slide open the battery cover on the back of the remote
transmitter.
2.
Install the AAA batteries into the remote control (see
Fig. 4
).
3.
Replace battery cover.
Dispose of batteries in the proper manner according to Provincial
and local regulations. Any battery may leak electrolyte if mixed
with a different battery type, if inserted incorrectly, if all the batteries
are not replaced at the same time, if disposed of in a fire or if an
attempt is made to charge a battery not intended to be recharged
.
Remote Control
Operation
Warning:
It takes some time for the receiver to respond to the
transmitter. Do not press the buttons more than once within two
seconds for correct operation.
Setting
Operation
Indication
Flame effect
Press the ‘
I
’ button once
Left Neon
Flame effect & 750W heat setting
Press the ‘
I
’ button again
Left & Middle Neon
Flame effect & 1500W heat setting
Press the ‘
I
’ button again
All 3 neon’s
To turn off any of the settings press the ‘
O
’ button once.
To increase or decrease the brightness of the fuel effect use the
buttons ‘
’ as shown in
Fig. 4
.
Lamp Replacement
To gain access to the lamps
1.
Remove the front frame (see ‘x’ in
Fig. 6
) by lifting out then
up and carefully leave to one side.
2.
Remove the three screws (see ‘y’ in
Fig. 6
) on the fuel
effect.
3.
Slide the fuel effect out, by holding the front ledge and set
aside carefully (taking care not to damage the logs as they
are fragile) – see
Fig. 6
.
4.
For access to the bulbs, carefully rotate the flexible
rotisserie out of position ensuring that the rubber grommet
is not lost – see
Fig. 7
.
5.
Unscrew the defective lamp anti-clockwise. Replace with
a 230V, 60W E14 SES lamp, do not over tighten (see
Fig. 7
).
6.
Refit the fuel effect (with three screws) and Front Panel.
Thermal Safety Cut-out
For your safety, this appliance has been fitted with thermal cut-
out. In the event that the product overheats, the cut-out switches
the heat off automatically.
To bring the heat back into operation, remove the cause of the
overheating, then unplug or turn off the electrical supply to the
heater for up to 10 minutes.
When the heater has cooled sufficiently, re-connect and switch
on the heater.
Caution: In order to avoid a hazard due to inadvertent resetting
of the thermal cut-out, this appliance must not be supplied
through an external switching device, such as a timer, or
connected to a circuit that is regularly switched on and off by
the utility
Cleaning and Maintenance
Warning: Always disconnect from the power supply before
attempting any maintenance.
Cleaning
Before commencing cleaning, unplug the heater and allow it to
cool.
The surface of the heater should be given an occasional wipe
over with a soft damp cloth. Do not use detergents abrasive
cleaning powder or polish on the body of the heater. The glass
screen should be cleaned carefully with a chamois leather. Do
not use proprietary glass cleaners.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not
be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for
recycling advice in your country.
After Sales Service
Your product is guaranteed for one year from the date of purchase.
Within this period, we undertake to repair or exchange this product
free of charge (excluding lamps & subject to availability) provided
it has been installed and operated in accordance with these
instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales information or assistance witn
this product please go to
www.dimplex.co.uk
where you will
find our self help guide by clicking on “After Sales” or ring our
help desk on 0845 600 5111.
Spare parts are also available on the website
www.dimplex.co.uk.
Please retain your receipt as proof of purchase.
[c] GDC Group Ltd,
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex.
A division of GDC Group Ltd,
DIMPLEX
MILLBROOK HOUSE
GRANGE DRIVE
HEDGE END
SOUTHAMPTON
SO30 2DF
TEL: 0845 600 5111
FAX: 01489 773050
WEBSITE: www.dimplex.co.uk
Republic of Ireland Tel.
01 8424833
