38
JOB/SEQUENCES
1 - Creating and saving / editing and overwriting a JOB/SEQUENCES (*)
JOB/SEQUENCES
„PI 3006.M PULS“ / „PI 4006.M PULS“ / „PI 4606.M PULS“ CONTROL PANEL
MENU K
Ey
ENTER/MEM K
Ey
ENCODER K
NOb
- SX
ENCODER K
NOb
- DX
D
iSplay
SX K
Ey
DX K
Ey
A
V
211 24.8
Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
PROGRAM 0011
(*) For the sequences, see the relevant paragraph in the settings menu.
CREATING AND SAVING A JOB
PRG JOB
PROCESS
I
001
MMA
97
002
--- ---
---
003
--- ---
---
004
--- ---
---
005
--- ---
---
011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
PRG JOB
PROCESS
I
001
MMA
97
002 0011 MIG/MAG SYNERGIC
211
003
--- ---
---
004
--- ---
---
005
--- ---
---
011 Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
To create and save a
JOB
(automatic welding point) proceed as follows:
•
During any welding process and at any time, once you have acquired the necessary parameters, hold
the
ENTER/MEM K
Ey
down for
3
consecutive seconds.
•
The
DISPLAY
automatically goes to the first free position in the
JOB
table.
•
Choose the position in which the
JOB
is to be saved by rotating the
ENCODER K
NOb
- SX
.
•
Push the
ENTER/MEM K
Ey
to confirm and finalise saving of the
JOB
created.
EDITING AND OVERWRITING A JOB
A
V
211 24.8
Fe G3 SI-1 Ø 0.8 Ar 16-20% CO2
PROGRAM 0011
002
PRG JOB
PROCESS
I
001
MMA
97
002 0011 MIG/MAG SYNERGIC
211
003
--- ---
---
004
--- ---
---
005
--- ---
---
OVERWRITE JOB 002?
To edit and/or overwrite a
JOB
proceed as follows:
•
During any welding process and at any time push the
MENU K
Ey
to exit the welding phase.
•
Select the welding process
JOB
by rotating the
ENCODER K
NOb
- SX
.
•
Push the
MENU K
Ey
to open the
JOB
table.
•
Select the
JOB
to be edited by rotating the
ENCODER K
NOb
- SX
.
•
Push the
ENTER/MEM K
Ey
to view the settings on the
DISPLAY
for the
JOB
to be edited.
•
Hold down the
ENTER/MEM K
Ey
for about
3
consecutive seconds, until the
DISPLAY
loads all the
parameters / data for the
JOB
onto the screen (making them available to the operator).
•
Acquire the parameters necessary for editing the
JOB
.
•
Hold down the
ENTER/MEM K
Ey
for
3
consecutive seconds.
•
The
DISPLAY
automatically goes to the first free position in the
JOB
table.
•
Choose the free position in which the edited
JOB
is to be saved, or a position already occupied in
which the edited
JOB
will be overwritten, by rotating the
ENCODER K
NOb
- SX
.
•
Push the
ENTER/MEM K
Ey
to confirm the operation.
•
Push the
SX K
Ey
to confirm the overwriting operation or the
DX K
Ey
to cancel it.
(continued)
„WF 793.M“ CONTROL PANEL
It is not possible to create, save, edit or overwrite a
JOB/SEQUENCE
using the „WF 793.M“ CONTROL PANEL.
Summary of Contents for DIX PI 3006.M PULS
Page 10: ...10 2101EA86 Wiring diagram ...
