background image

24L COMPRESSOR

BP24L20

MAINTENANCE

Warning! Before carrying out any maintenance or
adjustments the machine must be disconnected
from the mains power supply. 
1.The compressor must be drained completely by
loosening the water drain cock. Drain the air
receiver tank daily after use.
2. The air filter can be removed for either cleaning
or replacing. Clean the air filter element after
every 100 hours of use or if low pressure is
experienced. Replace the air filter after 200 hours
of use. Note: Under no circumstances should the
compressor be operated with the air filter
removed.
3.Cleaning and maintaining the compressor
regularly will give a long and trouble free life.
Before long term storage it is advisable to give the
compressor a thorough clean. This should include
the removal of all fitted accessories. Do not use
any solvents as these can damage plastic parts.
Only use a clean cloth dampened with warm
soapy water. Any metal parts should be given a
wipe with a light machine oil to prevent rusting.
CAUTION. Water must never come into contact
with the compressor.

SPARES HELPLINE
01302 721791

ENVIRONMENTAL PROTECTION

Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with
your Local Authority or retailer for
recycling advice.

Summary of Contents for BP24L20

















Reviews: