Directed Electronics 3100 Installation Manual Download

Page: 2 / 16

Contents

What is Included ................................................................................................. 1

Wiring Connections ............................................................................................. 2

Main Harness 12-pin Connector (H1) ..................................................... 2

Door Lock, 3-Pin Connector (H2) ............................................................ 3

Horn Honk, 3-pin connector .................................................................. 3

Starter Interrupt Harness (H3) ............................................................... 4

Plug-in LED and Valet Program switch ..................................................... 4

Internal Programming Jumper ............................................................................. 5

Light Flash ........................................................................................... 5

Onboard Dual Stage Zone 2 Impact Sensor .......................................................... 6

Bypassing Sensor Inputs ....................................................................................... 6

Nuisance Prevention Circuitry (NPC) ..................................................................... 7

Table of Zones ..................................................................................................... 7

Remote Control Programming............................................................................... 8

Function Table ..................................................................................... 9

System Feature Programming ............................................................................... 9

Feature Table..................................................................................... 10

Feature Descriptions ........................................................................... 11

Troubleshooting ................................................................................................. 13

Summary of Contents for 3100

















Search results

Summary of Contents for 3100

Reviews:

Related manuals for 3100

Brands by name

Popular brands

Directed Electronics 3100, Installation Manual

Search results

Summary of Contents for 3100

Reviews:

Related manuals for 3100

Brands by name

Popular brands