background image

12

© 2009 Directed Electronics. All rights reserved.

Double Lock Only: the lock output only will pulse twice 

3. 

Double Lock & Unlock: the lock & unlock outputs will pulse twice

4. 

6.  Door Lock Output Duration

0.8sec.: the door lock output pulses will be 800mS in duration

1. 

3.5sec.: the door lock pulses will be 3.5 seconds in duration

2. 

0.4 sec.: the door lock pulses will be 400mS in duration

3. 

 

7.  Ignition Controlled 2nd Unlock

After first unlock: for Ign-controlled unlocking, the 2nd unlock will activate 800mS after the first (driver 

1. 

door) unlock

With first unlock: for Ign-controlled unlocking, the 2nd unlock will activate at the same time as the first 

2. 

(driver door) unlock

8.  Comfort Closure

No comfort Closure: Comfort Closure is defeated when locking 

1. 

Comfort Closure 1: the door lock pulse (or 2nd pulse for double pulses) will remain on for 20 sec-

2. 

onds.

Comfort Closure 2: 800mS following the end of the door lock pulse (or 2nd pulse for double pulses); 

3. 

the door lock output will turn on again for 20 seconds.

9. Hood Switch Type

Normally Open: for vehicles with a hood switch that rests at ground when the hood is OPEN

1. 

Normally Closed: for vehicles with a hood switch that rests at ground when the hood is CLOSED

2. 

10. Door Switch Type

Normally Open: for vehicles with door switches that rest at ground when the door is OPEN

1. 

Normally Closed: for vehicles with door switches that rest at ground when the door is CLOSED

2. 

11. Remote Button Unlock (Ign off)

On: a message telling the remote control to unlock the keypad is sent each time the vehicle ignition 

1. 

is turned off

Off: no message is sent

2. 

Summary of Contents for Responder LE























Reviews: