background image

© 2003 Directed Electronics, Inc. Vista, CA

3

table of contents

warning! safety first . . . . . . . . . . . . . . . . . . . . . . . . 4

installation points to remember. . . . . . . . . . . . . . . . 5

before beginning the installation . . . . . . . . . . . . . 5
after the installation. . . . . . . . . . . . . . . . . . . . . . 5

deciding on component locations . . . . . . . . . . . . . . . 6

locations for the siren . . . . . . . . . . . . . . . . . . . . . 6
locations for the control module . . . . . . . . . . . . . . 6
locations for stinger doubleguard shock sensor . . . . 7
locations for valet/program switch . . . . . . . . . . . . 8
locations for the status LED . . . . . . . . . . . . . . . . . 8
locations for the optional starter kill relay . . . . . . . 9
locations for the relay satellite. . . . . . . . . . . . . . . 9

finding the wires you need . . . . . . . . . . . . . . . . . . . 9

obtaining constant 12V . . . . . . . . . . . . . . . . . . . . 9
finding the 12V switched ignition wire. . . . . . . . . 10
finding the starter wire . . . . . . . . . . . . . . . . . . . 10
finding the accessory wire . . . . . . . . . . . . . . . . . 11
finding the tachometer wire . . . . . . . . . . . . . . . . 11
finding the wait-to-start bulb wire for diesels  . . . 11
finding a (+) parking light wire. . . . . . . . . . . . . . 12
finding the door pin switch circuit . . . . . . . . . . . 12

making your wiring connections. . . . . . . . . . . . . . . 13

primary harness (H1), 12-pin connector . . . . . . . . . 14

auxiliary harness (H2), 6-pin connector . . . . . . . . . 14

door lock harness, 3-pin connector. . . . . . . . . . . . . 15

remote start ribbon harness, wiring diagram . . . . . . 15

heavy gauge relay satellite wiring diagram . . . . . . . 16

remote start harness (H3), 5-pin connector . . . . . . 16

primary harness (H1) wire connection guide. . . . . . 17

secondary harness (H2) wire connection guide . . . . 21

relay key switch interface wire connection guide. . . 23

remote start secondary harness (H3) wire  . . . . . . . . 
connection guide . . . . . . . . . . . . . . . . . . . . . . . . . 25

neutral safety switch interface. . . . . . . . . . . . . . . . 26

testing the neutral safety switch. . . . . . . . . . . . . 27

bypassing GM vehicle anti-theft systems (VATS) . . . 30

1995 and newer vehicle anti-theft systems  . . . . . . . 

(immobilizers)  . . . . . . . . . . . . . . . . . . . . . . . . . . 31

passlock I and passlock II (PL-1 and PL-2) . . . . . . 31
passkey III (PK-3), transponder-based systems . . . 31

plug-in LED and valet/program switch . . . . . . . . . . 32

programmer interface, 3-pin black plug . . . . . . . . . 32

shock sensor harness, 4-pin connector . . . . . . . . . . 33

tach learning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

programming jumpers . . . . . . . . . . . . . . . . . . . . . . 34

tach threshold on/off . . . . . . . . . . . . . . . . . . . . 35
light flash (+)/(-) . . . . . . . . . . . . . . . . . . . . . . . 35

transmitter/receiver learn routine™ . . . . . . . . . . . . 35

transmitter configurations . . . . . . . . . . . . . . . . . . . 37

standard configuration. . . . . . . . . . . . . . . . . . . . 37

multi-level security arming . . . . . . . . . . . . . . . . . . 38

system features learn routine . . . . . . . . . . . . . . . . 38

feature menus . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

menu #1 - basic features . . . . . . . . . . . . . . . . . . 40
menu #2 - advanced features . . . . . . . . . . . . . . . 41
menu #3 - remote start options . . . . . . . . . . . . . 41

feature descriptions . . . . . . . . . . . . . . . . . . . . . . . 42

menu #1 - basic features . . . . . . . . . . . . . . . . . . 42
menu #2 - advanced features . . . . . . . . . . . . . . . 43
menu #3 - remote start options . . . . . . . . . . . . . 45

nuisance prevention circuitry™. . . . . . . . . . . . . . . . 47

valet mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

timer mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

table of zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

shutdown diagnostics . . . . . . . . . . . . . . . . . . . . . . 49

to perform shutdown diagnostics . . . . . . . . . . . . 49

long term event history . . . . . . . . . . . . . . . . . . . . . 49

safety check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 51

alarm troubleshooting . . . . . . . . . . . . . . . . . . . . 51
remote start troubleshooting . . . . . . . . . . . . . . . 52

wiring quick reference guide . . . . . . . . . . . . . . . . . 54

relay satellite wiring quick reference guide . . . . . . 55

Summary of Contents for RS2.1
























































Reviews: