Preparatory work
Getting to know the appliance
Fig.
1
:
1
dust bin;
2
cord rewind button;
3
ex-
haust filter cover;
4
suction hose connection;
5
dust bin release;
6
dust bin handle;
7
dust
bin cover;
8
ON/OFF button;
9
parking brack-
et;
10
connection cord;
11
suction hose;
12
handle;
13
bypass vent;
14
suction hose release;
15
telescop-
ic tube;
16
telescopic tube release catch;
17
accesso-
ry bracket;
18
switchable floor nozzle;
19
crevice noz-
zle;
20
furniture brush;
21
mini turbo nozzle
Unpacking and assembling
1
Check that the unpackaged contents are com-
plete. If you notice any transport damage or if an-
ything is missing, contact your dealer immediate-
ly.
2
Connect suction hose and appliance (Fig.
2
).
3
Connect the suction hose with the telescopic tube
and adjust the length of the telescopic tube (Fig.
3
).
4
Connect telescopic tube and switchable floor noz-
zle (Fig.
4
).
5
Ensure that the bypass vent (Fig.
1
/
13
)
is completely closed.
Using the accessories
CAUTION!
For hard floors, only use the switchable floor
nozzle (Fig.
1
/
18
) with the brush (Fig.
10
) ex-
tended, as the hard floor may otherwise become
damaged.
CAUTION!
If using the turbo nozzle (Fig.
1
/
21
), make sure
that the surface can withstand the rotating brush
without becoming damaged.
NOTE:
You can also use the suction nozzles without the
telescopic tube as necessary. To do so, connect
the required accessories directly to the handle
(Fig.
9
).
1
Connect the required accessory to the handle or
the telescopic tube (Fig.
9
).
2
Make sure that the
accessory is securely connected.
➔
The appliance
can be connected.
Connecting the appliance
CAUTION!
If the red marking is visible (Fig.
6
/
1
), retract
the connection cord by pressing the cord rewind
button to pull in the cord up to the yellow mark
(Fig.
6
/
2
) (Fig.
7
). Otherwise, the connection
cord might be damaged.
1
Pull the cable out of the appliance (Fig.
5
).
2
In-
sert the plug into a mains socket.
Vacuum cleaning
Flexible vacuum-cleaning
1
Connect the required accessories >”Using the ac-
cessories” on page 17.
2
Connect the appliance
>”Connecting the appliance” on page 17.
3
To switch
on the appliance, press the ON/OFF button (Fig.
8
).
➔
The appliance vacuums at full suction pow-
er.
4
To reduce the suction power, open the by-
pass vent as required >”Regulating the suction pow-
er” on page 17.
5
To switch off the appliance, press
the ON/OFF button again (Fig.
8
).
➔
The appliance
switches off.
6
Close the bypass vent (Fig.
1
/
13
) so
that the appliance operates with full suction power
when vacuum-cleaning the next time.
Regulating the suction power
1
To reduce the suction power, slide the bypass vent
open (Fig.
11
).
2
To increase the suction power, slide
the bypass vent closed again (Fig.
11
).
Storing the appliance
NOTE:
If necessary, use the accessories mount (Fig.
1
/
17
)
to attach 2 accessories.
1
Switch off the appliance and pull the plug from the
socket.
2
Push the cord rewind button (Fig.
1
/
2
)
until the cord has been fully rewound (Fig.
7
).
3
Hang the telescopic floor nozzle or parquet nozzle
(connected to the telescopic tube or handle) in the
parking bracket (Fig.
1
/
9
) (Fig.
12
).
EN
17
