background image

Operating Instructions

Always wear safety glasses, safety shoes, and suitable work 

clothes when operating the log splitter. Do not wear neckties, 

scarfs or other loose clothing that could get caught in moving 

parts.

Keep hands and feet clear of the ram and wedge at all times.

Keep away from flammable liquids and gases before starting.

1)  Place the log splitter on a sturdy, level surface. Block the wheels 

to prevent movement of the log splitter during operation.

2) Make sure the handle is free of oil, grease and resins.

3) Oil the wedge and the top of the beam for smoother operation.

4)  Ensure the equipment is in safe working condition. Operate the 

unit without loading to make sure it is working normally. Check 

all nuts, bolts and hydraulic fittings are tight. Check the switch, 

power cable and plug for damage to avoid electric shock. Check 

that all safety shields are in proper position.

5)  Check that the outlet’s main voltage and frequency match the 

data stated on the model plate.

6)  Plug in the power cable and switch on the motor. NEVER use 

an extension cord longer than 25 feet. Minimum cord gauge 

must be 16. The power supply for this log splitter must have a 

protection device (circuit breaker) for over or under voltage.

7)  Place a log on the beam against the push plate. Make sure that 

the log is securely on the beam and up against the push plate. 

Logs should be cut with square ends and to a maximum length 

of 20 in. in advance. Always use extra care when splitting logs 

with unsquare ends.

8)  Two controls must be activated to operate the log splitter. The 

hydraulic control lever and the ON/OFF push button must be 

held during the splitting process. If either control is released, the 

log splitter will stop operating.

9) Loosen the bleed screw one or two turns if necessary.

10)  Depress and hold the ON/OFF push button with your right 

hand and allow the motor to cycle up to speed.

11) Push down on the hydraulic control lever.

12)  Release the ON/OFF button and the control lever when the log 

is split. The push rod will then retract.

13

!

WARNING

Summary of Contents for 100481

















Reviews: