background image

24(35)

 

  

 

User manual in Original 

 

Dok. ref: User manual 500A-ATF-K Rev. F  
DISPERATOR AB
 

  Tel: +46 8 724 0160 

E-mail: info@disperator.se 

Mälarvägen 9, SE-141 71 Segeltorp, Sweden    Fax: +46 8 724 6070 

Web page: www.disperator.se 

9.3.

 

Trouble Shooting 

9.3.1.

 

Disposer Reduces Speed, stops or does not start 

A humming sound might be heard from motor 
1.

 

Press the red button (0). 

 

2.

 

Use the main electrical safety switch to disconnect electrical supply. Lock the switch with a 
padlock or a cable tie if you need to leave the disposer temporarily before step 10 is completed. 

3.

 

Use protective gloves. Open the protective lid and check if something is jammed in the disposer. 

4.

 

If so, place the jam release wrench on the center washer. See picture below. 

  

5.

 

Release the grinder by rotating the wrench backwards and forwards until the shredder  
rotates freely in both directions. If needed, extend the bar on the wrench and hit  
the bar with a hammer.  

6.

 

Remove the jam release wrench. 

7.

 

Remove any non grindable objects; for example cutlery.  

8.

 

Close the protective lid. Make sure that the safety interlock switch connects. 

9.

 

Check fuses/breakers. Change/reset if needed. 

10.

 

Use the main electrical safety switch to connect the electrical supply. 

11.

 

Press the green button (1) to start and empty the disposer. 

9.3.2.

 

The Disposer starts but there is no Flushing Water 

1.

 

Is the stop valve in the water supply pipe open? If not, open stop valve.  

2.

 

Is a clicking sound heard when activating the solenoid valve? If not, change the coil. 

3.

 

Is the line strainer clogged? Turn off water supply, open strainer and clean. Close strainer carefully 
without damageing the seal, and make sure it is thight when disposer is restarted. 

 

9.3.3.

 

The Disposer does not start and makes no Sound 

1.

 

Is the protection lid closed properly? 

2.

 

Check the main electrical safety switch; make sure that it is in an ON-position. 

3.

 

Check fuses/breakers. Change/reset if needed. 

4.

 

Press the red button (0) to reset the motor protector. 

 
If the fault cannot be remedied please contact authorized service personnel or 
Disperator AB / local representative. Always provide the disposer’s serial number 
when contacting Disperator. 

Summary of Contents for 500A-ATF-K




































Reviews: