background image

8(35)

 

  

 

User manual in Original 

 

Dok. ref: User manual 500A-ATF-K Rev. F  
DISPERATOR AB
 

  Tel: +46 8 724 0160 

E-mail: info@disperator.se 

Mälarvägen 9, SE-141 71 Segeltorp, Sweden    Fax: +46 8 724 6070 

Web page: www.disperator.se 

1.2.

 

Personnel Qualifications and Training 

All personnel operating, performing maintenance, inspecting or installing the disposer must be 
properly trained and qualified. Areas of responsibility, scope of authority and staff supervision must be 
defined by the owner. If personnel do not have the necessary qualifications, they must receive training 
and instructions. Training can be provided by the supplier/manufacturer. It is the responsibility of the 
owner of the disposer to make sure that all users read and understand this User Manual. 

 

Transportation 
Personnel responsible for transporting the disposer must be familiar with accident prevention 
regulations for any hoisting gear and lifting accessories to be used. Handlers should be given 
appropriate instructions prior to undertaking transportation, hoisting and lifting. 

 

Installation 
Personnel responsible for installing the disposer must be trained as an industrial mechanic/technician. 
The electric connection must be performed by trained and certified electricians. 
 
Start-up and Maintenance 
Personnel responsible for start-up and maintenance of the disposer must be familiar with its design 
and functions. They must understand the operating principle of the disposer and have read the 
manual and the safety instructions before commencing work. 
 
Operation 
All persons who operate the disposer must be aware of the risks associated with the operation of the 
disposer, which are described in this manual. 
 
Service and Repair 
Personnel responsible for service and repair of the disposer must have training as, or equivalent to, 
industrial mechanics/technicians. They must also have knowledge of, and be aware of, the specific 
details of the disposer, as described in this manual. Unskilled personnel must be trained and any 
repair work undertaken must be checked by the owner. 

 

 

Summary of Contents for 500A-ATF-K




































Reviews: