disperator EXCELLENT 500A-MB Series, User Manual

User manual in Original

Doc. ref: 500A_MB_am_en_210602
DISPERATOR AB

Tel: 08-724 0160   

E-mail: info@disperator.se

Mälarvägen 9, 141 71 Segeltorp   

We page: www.disperator.se

32 / 41

Position No

:

Qty:

Denomination:

Spare Part No:

Included in              

Service Package:

P1

1

Motor with drained upper flange

-14

P2

1

Carrier

-18

2

P3

1

End shield

-13

P4

1

Washer for V-ring seal

-03/00

1 and 2

P5

2

Axle seal, with stainless spring

-03/02

1 and 2

P6

1

Locking ring

-03/03

1 and 2

P7

4

Screw for end shield assembly

-23

1 and 2

P8

1

V-ring seal

-03/01

1 and 2

P9

1

Key for carrier

-10

1 and 2

P10

1

Rotary shredder

-02

2

P11

1

Axle washer

-06

2

P12

1

Axle screw

-07

1 and 2

P13

1

Stationary shredder

-01

2

P14

1

Seal for stationary shredder

-05

1 and 2

P15

1

Hood

-16

P16

4

Locking nut and washer for hood assembly

-25

1 and 2

P17

1

Seal for hood flange

-08

1 and 2

P18

6

Screw and nut for disposer assembly

-22

1 and 2

Below parts with Pos. No. P19 – P25 are not used for disposers installed in closed cabinet models

P19

1

Strap for housing

-17

P20

1

Housing

-15

P21

1

Sealing list for housing

-15/01

P22

1

Cable gland with nut

-19

P23

2

Screw and washer for housing assembly

-26

1 and 2

P24

3

Adjustable disposer leg (only for Model 520, 530, 550 and 575)

-29

P25

3

Screw for disposer leg 

-29/01

1 and 2

Not depicted parts

P26

1

Special grease for seals and carrier

-04

1 and 2

P27

1

Rubber sealing compound

-09

1 and 2

P28

2

Axle seal, motor drive end and motor non-drive end

-14/01

P29

2

Bearing, motor drive end and motor non-drive end

-14/02

P30

1

Key for motor shaft 

-14/03

P31

1

Disassembly screw for carrier

-18/02

2

Parts depicted on the next page

P17

1

Noise damping seal (alternative to spare part No. -08)

-08/1

P32

1

Torque protection bar for fixation of disposer in wall/bulkhead

-28/V

P33

1

Jam release wrench for rotary shredder

-31

P34

1

Solenoid valve, G½” (BSPP), internal thread, incl. coil, cable plug and 

fixating washer

-35

P35

1

Coil for solenoid valve

-36

P36

1

Line strainer, G½” (BSPP), internal thread  

-37

P37

1

Start & stop unit incl. contactor with motor overload protector

-38

P38

1

Contactor with coil

-38/1

P39

1

Start contact

-38/2

P40

1

Motor overload protector

-38/3

P41

1

Interlock switch 

-39

Always state machine serial number and spare part number (see above) when ordering spare parts.

NOTE!  That the correct quality and strength of all nuts and screws used are important. Disperator can not guarantee the safety if 

other screws and nuts than those ordered from us are used.