DITTING 1203 Series Service Tips Manual Download

Page: 5 / 9

www.ditting.com

ERVING THE

HOLE

-B

EAN

OFFEE

ARKET

INCE

1968 info@ditting.com

U.S. Distribution Center

8801-B Smiths Creek Rd, Wales, MI 48027
Tel 810-367-7125 Toll-Free 800-835-5992

Fax 810-367-7130

Serving the Whole-Bean

Coffee Market Since 1968

www.ditting.com

Ref. Models:

1403 Series
1800 Series

ERVICE

#R2

TROUBLESHOOTING ALL DITTING

220 VOLTS, 3 PHASE G

RINDERS…1403 AND 1800 SERIES

Our motors do not burn out easily. Look for simple problems. Never assume that the motor is bad because the
grinder is doing something unusual.

PROBLEM

CHECK FOR

POSSIBLE SOLUTION

NO OUTPUT

Coffee does not come out

DIRECTION OF ROTATION:

Looking into the hopper, when
the grinder comes to a stop, it
should be turning counter-
clockwise.

REVERSE ANY TWO OF THE HOT
WIRES (DO NOT CHANGE THE YELLOW
OR YELLOW-GREEN GROUND WIRE) IN
THE PLUG.

This needs to be done when

the grinder is first installed or plugged into a
new outlet.

GRINDER CHANGES
DIRECTION OF
ROTATION EVERY TIME
IT IS TURNED ON

ONE OF THE THREE
PHASES IS NOT
DELIVERING POWER TO
THE MOTOR

THE PROBLEM IS ONE OF:

BAD SWITCH (KFA1403 version)

BAD WIRE IN THE PLUG OR OUTLET

(any model)

BAD CONTACTOR (KFR/KR model)

GRINDER STOPS UNDER
LOAD

Runs okay without beans
but stops when beans are
added

ONE OF THE THREE
PHASES IS NOT
DELIVERING POWER TO
THE MOTOR

THE PROBLEM IS ONE OF:

BAD SWITCH (KFA1403 version)
BAD WIRE IN THE PLUG OR OUTLET

(any model)

BAD CONTACTOR (KFR/KR model)

GRINDER STAYS ON

BAD CONTACTOR

KFR OR KR1403

Replace contactor

BREAKER KEEPS
TRIPPING OFF

SHORT CIRCUIT

LOOK FOR BURNED OUT WIRE
SHORTING TO THE GRINDER HOUSING
EITHER AT THE BASE OF THE MACHINE
OR IN THE SWITCH AREA, OR LOOK
FOR A CRIMPED WIRE AT THE BASE.

GRINDING TOO
SLOWLY and/or
OVERHEATING

WORN OUT GRINDING
DISCS

, or worn out/broken

fins on the lower rotating plate

REPLACE THE GRINDING DISCS

, and/or

REPLACE THE LOWER ROTATING
PLATE.

Visit our website at

www.ditting.com

for this and other service tips.

Summary of Contents for 1203 Series










Search results

Summary of Contents for 1203 Series

Reviews:

Related manuals for 1203 Series

Brands by name

Popular brands

DITTING 1203 Series, Service Tips Manual

Search results

Summary of Contents for 1203 Series

Reviews:

Related manuals for 1203 Series

Brands by name

Popular brands