PROGRAMMING
P-SERIES
Page 10 of 76
SBC
PROGRAMMING METHOD
AUGUST 2003
P-SERIES
i
The controller has two modes of operation:
NORMAL and SERVICE.
NORMAL MODE:
In Normal Mode, on power up display will show the software version installed in vender for 10 Seconds, then
change to Ice Cold Drink message, Product Price, Sold Out, Credit Value, or decimal point. If the right most
decimal is flashing, this indicates an error or problem recognized in the vender. When money is inserted, the
display indicates the total amount of the deposit. The select buttons are used to select the product. In normal
mode you may access an external menu for reading historical sales total, product total, product total by selection,
sales by price totals, and machine temperature.
Note:
If ” SCOL” appears on the display on power up with the door open, you will need to program the vender
model number in the controller.
Refer to Setting The Vender Type
on page 8.
SERVICE MODE:
The Service Mode is entered when the vender door is open and the service switch is pressed. The display will
show a list of error codes for errors that have occurred since the door was last opened. VS is a vend sensor
problem, HS # is a vend mechanism home sensor problem, CJ # is a vend mechanism jammed, SS # is a select
switch problem, RFRG is a refrigeration or temp sensor problem, and DS is a door switch open problem. To
acknowledge an error, press select button 1, at this time you will enter the service menu. The display will show
HD
at this time. Some of the menu items have sub-menus.
To move through the menus and sub-menus follow these instructions. To:
MOVE THROUGH MENU:
Press select buttons 1 & 2 simultaneously to scroll down through the menu.
While scrolling down through menu, release for 2 seconds, press select
buttons 1 & 2 simultaneously to scroll up through menu.
ENTER SUB-MENU:
Press and hold select button 1 to enter a sub-menu.
EXIT SUB-MENU:
With "Return" (RTN) on display, press and hold select button 1 to exit a
sub-menu.
EXIT SERVICE MODE:
Closing the inner door, pressing select button 1 when RTN is displayed at the top menu level, pressing the
service button a second time, or a five-minute inactivity time-out will exit the service mode.
Summary of Contents for DN552P-7
