INSTALLATION & SETUP
P-SERIES
Page 7 of 76
Loading Product
The P-Series Vender is designed to vend a wide
range of packages.
All P-Series Venders are shipped ready to vend
packages according to customers orders. To vend
an alternative package in the P-Series vender,
contact Dixie Narco Technical Service Dept. or your
Representative for assistance.
INITIAL LOADING
To ensure proper vending, make sure wide columns
are set to vend the proper packages. When loading
a wide column, the first row of packages should be
loaded on the bottom bar of the oscillator. The
second row of packages must be loaded on the top
bar of the oscillator. Always load complete rows; do
not load only to the back or only to the front of the
column.
The narrow column rotors must be in the “cup”
position to receive the first row of packages. When
loading narrow columns, lay the first row of
packages in the rotor. The second row of packages
must be loaded on the load bar.
Correct loading will prevent service calls and ensure
proper vending.
After loading the vender for the first time, ensure the
vender is loaded and primed. Priming is done in
programming.
The depth must also be
programmed depending on the package to be
vended. Cans may be programmed up to 4 deep.
NOTE: To ensure proper airflow through the
evaporator, DO NOT place packages (or
other foreign objects) in the bottom of the
tank.
SERVICE NOTE
Battery Backup (SBC)
The Single Board Controller is equipped with a battery
backup which is used to retain information programmed in
the system (pricing, time, date, etc.) in case of power
interruptions or any time the main power is off. When the
vender is shipped, the battery is connected and memory is
being maintained.
Disconnect the battery if the vender will be stored for a long
period of time. The following steps will guide you through
this procedure.
Ø
Remove power from the vender by unplugging the
main power cord from the wall receptacle.
Ø
Locate the Control Board on the main door.
Remove the battery from its holder (B1).
Summary of Contents for DN552P-7
