background image

25

TO REPLACE HEADLIGHT BULB

• Raise 

hood.

•  Pull bulb holder out of the hole in the backside of the 

grill.

•  Replace bulb in holder and push bulb holder securely 

back into the hole in the backside of the grill.

• Close 

hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run 

poorly, stop running, or prevent it from starting.
• Check 

wiring.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse.  The 

fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY 

(See Fig. 38)

• Raise 

hood.

•  Unsnap headlight wire connector.
• 

Stand in front of tractor.  Grasp hood at sides, tilt toward 

engine and lift off of tractor.

•  To replace, reverse above procedure.

Fig. 38

TRANSMISSION 

REMOVAL/RE PLACE MENT

Should your transmission require removal for service or 

re place ment, it should be purged after reinstallation and 

before operating the tractor.  See “PURGE TRANS MIS SION” 

in the Operation section of this manual.

HEADLIGHT

WIRE

CONNECTOR

HOOD

SERVICE AND ADJUSTMENTS

ENGINE

TO AD JUST THROTTLE CON TROL CABLE 

The throttle control has been preset at the factory and 

ad just ment should not be necessary. If adjustment is nec-

 es sary, see engine manual.

TO AD JUST CHOKE CON TROL 

The choke control has been preset at the factory and ad just-

 ment should not be necessary. If adjustment is necessary, 

see engine manual.

Summary of Contents for D15KH30

































Reviews: