17
SPARK PLUGS
Replace spark plugs at the beginning of each mowing
season or after every 100 hours of operation, whichever
occurs first. Spark plug type and gap setting are shown in
“PROD UCT SPECIFICATIONS” section of this manual.
00667
FUEL FILTER
CLAMP
CLAMP
IN-LINE FUEL FILTER (See Fig. 17)
The fuel filter should be replaced once each season. If fuel
filter becomes clogged, ob struct ing fuel flow to car bu re tor,
re place ment is re quired.
•
With engine cool, remove filter and plug fuel line sec tions.
• Place new fuel filter in position in fuel line with arrow
pointing towards carburetor.
• Be sure there are no fuel line leaks and clamps are
properly positioned.
• Immediately wipe up any spilled gasoline.
Fig. 17
MAINTENANCE
Fig. 18
•
Keep finished surfaces and wheels free of all gasoline,
oil, etc.
• Protect painted surfaces with automotive type wax.
Except for the washout port (if equipped), we do not
recommend using a garden hose or pressure washer to
clean the outside of your tractor unless the engine and
transmission are covered to keep water out. Water in
engine or transmission will shorten the useful life of your
tractor. Use compressed air or a leaf blower to remove
grass, leaves and trash from outside tractor and mower.
CLEANING (See Fig. 18)
• Clean engine, battery, seat, finish, etc. of all foreign
matter.
• Clean debris from steering plate. Debris can restrict
clutch/brake pedal shaft movement, causing belt slip
and loss of drive.
CAUTION:
Avoid all pinch points and
movable parts.
CLUTCH/BRAKE PEDAL
STEERING
PLATE
STEERING SYSTEM, DASH, FENDER AND MOWER NOT SHOWN
CLEAN
TOP SIDE
WASHOUT
PORT
HOSE
HOSE CONNECTOR
(12mm FEMALE)
WARNING: A broken or missing washout
fitting could expose you or others to
thrown objects from contact with the blade.
•
Replace broken or missing washout fitting
immediately, prior to using mower again.
•
Plug any holes in mower with bolts and locknuts.
Fig. 19
DECK WASHOUT PORT (See Fig. 19)
Your tractor’s deck is equipped with a washout port on
its surface as part of its deck wash system. It should be
utilized after each use.
• Drive the tractor to a level, clear spot on your lawn, near
enough to a water spigot for your garden hose to reach.
IMPORTANT:
Make certain the tractor’s discharge chute
is directed AWAY from your house, garage, parked cars,
etc. Remove bagger chute or mulch cover if attached.
• Make sure the attachment clutch control is in the
“DISENGAGED” position, set the parking brake, and
stop the engine.
• Ensure your garden hose is fitted with a standard 12mm
female hose connector (at the opposite end from the
tap connection).
• Pull back the lock collar of the hose connector and push
the connector onto the deck washout port at the left end
of the mower deck. Release the lock collar to lock the
connector on the nozzle.
IMPORTANT:
Tug hose ensuring connection is secure.
• Turn the water on.
• While sitting in the operator’s position on the tractor,
re-start the engine and place the throttle lever in the
Fast "
" position.
IMPORTANT:
Recheck the area making certain the area
is clear.
• Move the tractor’s attachment clutch control to the
“ENGAGED” position. Remain in the operator’s position
with the cutting deck engaged until the deck is cleaned.
• Move the tractor’s attachment clutch control to the
“DISENGAGED” position. Turn the ignition key to the
STOP position to turn the tractor’s engine off. Turn the
water off.
• Pull back the lock collar of the hose connector to
disconnect the connector from the nozzle washout port.
• Move the tractor to a dry area, preferably a concrete or
paved area. Place the attachment clutch control in the
“ENGAGED” position to remove excess water and to
help dry before putting the tractor away.
