background image

FlameWheel 450 

User Manual 

6

 

©

 2015 DJI. All Rights Reserved. 

Propeller Mounting Description

Attach the propeller with a silver nut onto the 
counter clockwise motor.

Attach the propeller with a black nut onto the 
clockwise motor (which has an indent on the 
screw).

Lock:  Tighten the propeller by rotating  
 

it in this direction. 

Unlock:  Remove the propeller by  
 

rotating it in this direction.

Black nut (9450 cw)

Silver nut (9450)

ESC and Motor Wiring Description

1. Please solder each ESC to the power pads on the bottom board as shown in the figure 

below. Make sure that the solder is firmly attached on the power pads and that there is no 
possibility for a short circuit. The power cable is a coaxial power cable. Do not damage the 
protector on the red cable to avoid short circuit. The red core of the coaxial power cable 
is positive, and the shielding layer of the coaxial power cable is negative. Make sure to 
solder them correctly at the proper length (the wires should be just long enough to reach 
the soldering point, face outwards, and should not be bunched up in front of the soldering 
point).

2. Connect the signal cable to your controller. The orange wire of the signal cable is for the 

control signal; the brown wire of the signal cable is for the GND.

3. Connect the motor to the ESC. Test the motor and make sure the rotation direction of each 

motor is correct. If not, switch the position of any two cables that are connecting the motor 
to the ESC to change the rotation direction.

+

_

+

_

+

_

+

_

+

_

Connect to the battery

Motor

Power cable

ESC

ESC cable

To the controller

Summary of Contents for FlameWheel 450










Reviews: