background image

- 1 -

ENLARGE ART FROM BOOK BY 125%

3 / 2015

How to Use the Tachymeter

This feature is found on watches that are made for speed measurement. The tachymeter scale is located on the case top ring or 
inner dial ring. It can be used to measure speed in miles per hour, knots, or kilometers per hour, using the scale on the ring.

Example of usage:
In a driving race, the car passes the first mile (km) post when the seconds hand is at the 12:00 position (60 seconds mark). 
Commence measurement.  At the 40 second mark the car passes the second mile (km) post, you will see that the car traveled a 
distance of one mile at 90 miles (km) an hour.

ENGLISH

Use Precautions - Resistance to Water

Important Watch Information

*  When the watch is underwater or wet, never use the pushers/bezels, or set the time. Watch cases and metal bracelets should be rinsed thoroughly in fresh water after being in salt water.
*  No backward hand or date adjustments should be made when the analog hands read between 8pm and 3am. At these times, the gears are too close together and such a change could cause damage.
*  No hot tub/sauna. Please do not take your DKNY watch into the hot tub/sauna. The combination of extreme heat and water may cause your watch to lose some of its water-resistance.

Date Models

Date Setting
1. Pull the crown out to position 2.
2. Turn the crown either clockwise or counter-clockwise and set the date for the previous day. The direction that moves the date 

varies on different watch models.

Time Setting
1. Pull crown out to position 3.
2. Turn counter-clockwise to advance the time and continue until the day changes to the present day.
3. Set to the correct time.
4. Push crown back to position 1.

3-Hand with Date Eye

    6P26

Time Setting
1. Pull crown out to position 2.
2. Rotate crown to set time.
 NoTe:  When setting the minute hand, move to 5 minutes earlier than time to be set, then turn it back to the correct time.
3. Return crown to position 1.

Date Setting
1. Pull crown out to position 2.
2. Rotate crown counter-clockwise to set date.
3. Return crown to position 1.
 NoTe: Do not set date between 9:00 p.m. and 12:00 a.m. or date will not change correctly.

DATE

DATE

WATER RESISTANcE

WATER-RELATED USE

Caseback Marking

Depth

 

Washing  

Hands

Showering,  

Bathing

Swimming, Snorkeling

Scuba  

Diving

WR

3 ATM

3 Bar,  

30 Meters

5 ATM

5 Bar,  

50 Meters

10 ATM

10 Bar,  

100 Meters

20 ATM

20 Bar,  

200 Meters

30 ATM

30 Bar,  

300 Meters

50 ATM

50 Bar,  

500 Meters

Always set the crown in closed position (the normal position). Tighten screw-lock crown completely.

Summary of Contents for 1970










Reviews: