background image

DMEGC Photovoltaic Modules Installation Manual

- 15 -

solar manufacturers' maintenance instructions for all components used in the system, such as support
frames, charging regulators, inverters, batteries etc.

8. Disclaimer of liability

Because the use of this manual and the conditions or methods of installation, operation, use and

maintenance of photovoltaic (PV) product are beyond DMEGC’s control, DMEGC does not accept
responsibility and expressly disclaims liability for loss, damage, or expense arising out of or in any way
connected with such installation, operation, use or maintenance.

No responsibility is assumed by DMEGC for any infringement of patents or other rights of third

parties, which may result from use of the PV product. No license is granted by implication or otherwise
under any patent or patent rights.

The information in this manual is based on DMEGC’s knowledge and experience and is believed to be

reliable; but such information including product specification (without limitations) and suggestions do not
constitute a warranty, expresses or implied. DMEGC reserves the right to change the manual, the PV
produce, the specifications, or product information sheets without prior notice.

Summary of Contents for DM M2-60BW Series




















Reviews: