background image

Do not disassemble the device without permission, which may cause device failure, and will 

Please do not use device on the following occasions:

reduce the waterproof performance of device.

waterproof performance of the device.

Please do not damage the device and the label on the back of the battery, otherwise it will reduce the 

In the launch, the device is not too close to or contact with the exposed parts of the body (especially 

Before installing options, be sure to turn off the device power supply.

Device and battery do not charge when wet.

Notice of using device:

Please keep this manual. 

IMPORTANT ITEMS

Ƹ

!

z

z

z

z

Ƹ

!

z
z
z
z
z
z
z
z

Precautions for battery use:

Please do not disassemble or refit batteries.
There is a protective circuit inside the battery, disassembly or modification of the battery will lead to damage 
to the protection circuit, the battery may produce smoke, rupture or fire.
Do not short-circuit the battery.
Do not use any metal to connect the battery "+" pole and "-" pole, do not use metal object 
container to store and store battery. If the battery is short circuited, it will produce too 
large current, the battery will heat, smoke, break or fire.
Please do not place the battery near the fire, stove or other heater. Please don't burn or heat the battery. 
Batteries can produce heat, fireworks, breaks, or fires.
Do not expose the battery to rain, snow, sea water or any other liquid.
Do not charge or use wet batteries. If the battery gets wet, it must be dried before use.

Precautions for charger:

Please do not plug the vent of the charger, otherwise it may cause internal parts damage and cause electric shock or fire.
Please don't let the charger close to the radiator or heat source; please don't pad the paper under the charger.
Please do not put the charger in a closed container and on the bed, sofa or carpet.
Please do not use the charger in the bathtub, the pool, the swimming pool or the wet basement.
Please do not place the metal sheet in a holder, otherwise the conductive material may damage the machine.
Please don't press the power supply to bend or twist the pins.
Please do not allow the charger to have stains, dust, water traces or food.
Please do not put the charger in high temperature or exposure to the sun.

Please read the instructions carefully before using.

The direct mode, transfer mode, a cluster mode of operation, please consult your dealer.

Ƹ

!

z
z
z
z
z

z

z
z
z

z

z

Ƹ

!

z
z
z

Please do not place the interphone on the unstable surface.

Please don't press the PTT key when you don't want to talk.

the face and eyes), please keep the antenna more than 2.5 centimeters away from the body.
When launching, the distance between the mouth and the microphone is 5 to 10 centimeters, which makes 
the sound clearer and reduces the electromagnetic radiation.
Headset headset connected to intercom, please reduce the volume of interphone.
Please do not use the option which is not made by our company.

Do not place the radio at places where the ambient temperature is below -30 or above +60 centigrade or 
in direct sunlight.

Near explosive sites.
On the plane.
Near the gas station.

+40

Summary of Contents for DM-1260












Reviews: