background image

Installation guide

13

dnp Supernova™ 

Flex Classic

To set a new TOP position (not recommended):

A. 

Remove the battery cover

B. 

Press the small right button (P2) shortly, until LED lits. If the button is held  
too long (> 3 seconds), and a beep is heard, redo this step.

C. 

Wihtin 3 seconds after step B, press the Upper button (2) and release 
(This step puts the screen in a mode to set the top position)

D. 

Use the Upper button (2) and/or Lower button (3) to adjust the screen to the 
desired position 

(Tip! When the screen is moving up, press Upper button (3) to 

stop the screen. When the screen is moving down, press Lower button (2) to 
stop the screen).  
CAUTION! Be careful not to set the top position too high. There must be space 
between the bottom bar and the cabinet. If the top position is set too high, 
and the bottom bar is touching the cabinet, permanent stress is applied to the 
bottom bar when the screen is up. This may lead to the bottom bar separating 
from the screen fabric over time. This is NOT covered by the dnp warranty.

E. 

When the screen is in the desired position, press and hold the Middle button (4) 
untill a beep is heard. (This indicates the screen is set)

Adjusting screen tension

The tension the Supernova Screen was adjusted at the factory, prior to shipping, however it may be necessary to re-adjust the 
screen tension after the screen is installed. To adjust the screen tension follow these steps:

waves/bulges

waves/bulges

Adjustment Screw (black colour)

Do not use (silver colour)

waves/bulges

waves/bulges

Adjustment Screw (black colour)

Do not use (silver colour)

In case of veritcal waves/bulges like above, turn screw 
“clockwise” until the waves/bulges disappear.

Please note that the range where waves/bulges 
disappear are quite narrow. Watch the screen 
while adjusting the tension for optimal result

Turn screw “clockwise” for increased tension 
Turn screw “counterclockwise” for decreased tension

In case of horisontal waves/bulges like above, turn screw 
“counterclockwise” until the waves/bulges disappear.

1

2

3

4

Summary of Contents for Supernova Flex Classic
















Reviews: