background image

 

 

13

 

 

WORK ONLY IF THE  ENGINES ARE OUTSIDE OR IN A WELL VENTILATED POINT. THE EXHAUST GAS OF 
THE ENGINES IS ODOURLESS AND ITS INHALATION CAN CAUSE SERIOUS OR FATAL ACCIDENTS. 
 
THE CONTACT WITH ELECTRIC ENERGIZED LINES CAN BE FATAL 

 

 

Pay the maximum attention when you cut, demolish, drill, etc. near energized electric lines that can 
be buried, walled or hidden. 

 

 

 

Be very careful also to gas and water pipes, telephone lines or other buried cables or ducts.

 

 

 

The working area must be free from objects that may fall, get spoiled, catch fire, make trip up or make 
the operation difficult or dangerous. 

 

 

Warn and move away imprudent bystanders or other people not authorized or involved with the job.  

 

 

If you work in narrow or closed rooms always plan a way out that must be kept free. 

 

 

Before using the equipment make sure and prevent vehicles, machines or people from passing on the 
equipment hoses or cables. 

 

 

Always connect tools to the power pack or other power sources before starting the engine. 

 

 

Keep in a safe dry place this manual and its enclosures, so they can be always available for future 
consultations. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for KOLUBRA


























Reviews: