manualshive.com logo in svg

Docomo F-05A, Instruction Manual

The Docomo F-05A is a sleek and stylish mobile phone equipped with advanced features. Ensure that you make the most of your device by downloading the free Instruction Manual from 88.208.23.73:8080. This manual provides detailed guidance on using the phone efficiently, making it a must-have for all users.

Share
Download
background image

37

AT&D<n>

*1

Set the operation performed when circuit ER (DTR) signal received from DTE is switched 
from ON to OFF while online data mode takes effect.
n=0 : Ignore status (status is always considered to be ON)
n=1 : Move to online command mode when status changes from ON to OFF
n=2 : Disconnect line and move to offline mode when status changes from ON to OFF 

(default)

AT&D2
OK

AT&E<n>

*1

Set type of speed display used when connection is made.
n=0 : Display communication speed of wireless zone
n=1 : Display communication speed between a PC and FOMA terminal (default)

AT&E1
OK

AT&F

The AT command settings in FOMA terminal are reset to the default.
When this command is executed during communication, the terminal is reset after the line 
is disconnected (displaying "NO CARRIER").

AT&F
OK (When in offline mode)

AT&S<n>

*1

Set control of the data set ready (DR) signal to be output to DTE.
n=0 : Always ON (default)

n=1 : ON at time of connection

AT&S0
OK

AT&W

Register the current settings in FOMA terminal.

AT&W
OK

AT

＊

DANTE

Indicate FOMA terminal reception level in the "

＊

DANTE : <n>" format.

n=0 : Out of service area
n=1 : Received signal level of FOMA terminal is 0 or 1 antenna.
n=2 : Received signal level of FOMA terminal is 2 antennas.
n=3 : Received signal level of FOMA terminal is 3 antennas.
AT

＊

DANTE=? : Display a list of displayable values

AT

＊

DANTE

＊

DANTE : 3

OK

AT

＊

DGANSM=<n>

*2

Set to reject or permit incoming packet communications.
n=0 : Reject setting = OFF, Accept setting = OFF (default)
n=1 : Reject setting=ON

n=2 : Accept setting=ON

AT

＊

DGANSM? : Display current settings

AT

＊

DGANSM=? : Display a list of assignable values

AT

＊

DGANSM=0

OK

AT

＊

DGAPL=<n> [,<cid>]

*2

Set the dialup connections (APN) to permit incoming packet communications. APN uses 
<cid> defined by +CGDCONT command.
n=0 : Add to list of APN permitted for incoming communications
n=1 : Delete from list of APN permitted for incoming communications
If the <cid> is not defined by the +CGDCONT command, it can still be added to/deleted from 
the list.
If the <cid> is omitted, all the <cid> are added to/deleted from the list.
AT

＊

DGAPL? : Display current settings

AT

＊

DGAPL=? : Display a list of assignable values

AT

＊

DGAPL=0,1

OK

AT

＊

DGARL=<n> [,<cid>]

*2

Set the dialup connections (APN) to refuse incoming packet communications. APN uses 
<cid> defined by +CGDCONT command.
n=0 : Add to list of APN rejected for incoming communications
n=1 : Delete from list of APN rejected for incoming communications
If the <cid> is not defined by the +CGDCONT command, it can still be added to/deleted from 
the list.
If the <cid> is omitted, all the <cid> are added to/deleted from the list.
AT

＊

DGARL? : Display current settings

AT

＊

DGARL=? : Display a list of assignable values

AT

＊

DGARL=0,1

OK

AT

＊

DGPIR=<n>

*2

Set whether to send caller ID when packet communication connection is being established. 
This command is available when a communication is sent or received.
n=0 : Connect to APN directly (default)

n=1 : Connect to APN prefixing 184

n=2 : Connect to APN prefixing 186
When Show/Hide caller ID is specified by dialup network

→

P20

AT

＊

DGPIR? : Display current settings

AT

＊

DGPIR=? : Display a list of assignable values

AT

＊

DGPIR=0

OK

AT

＊

DRPW

Indicate an index for the reception power of the radio waves that FOMA terminal receive.
AT

＊

DRPW=? : Display a list of displayable values

AT

＊

DRPW

＊

DRPW : 0

OK

Upper slot : Command   

Lower slot : Example

Description

Summary of Contents for F-05A






















































































































































































































































































































































































































Reviews:

No comments

Related manuals for F-05A

Samsung Galaxy TAB4 Manual preview
Galaxy TAB4
Brand: Samsung Pages: 38
Camrivox Flexor 500 Quick Install Manual preview
Flexor 500
Brand: Camrivox Pages: 4
Blackberry 8700 - 8707H SMARTPHONE Getting Started Manual preview
8700 - 8707H SMARTPHONE
Brand: Blackberry Pages: 48
qua Phone PX Settings Manual preview
Phone PX
Brand: qua Pages: 2
Thrane&Thrane Capsat TT-3060A User Manual preview
Capsat TT-3060A
Brand: Thrane&Thrane Pages: 182
DOPOD C720W User Manual preview
C720W
Brand: DOPOD Pages: 352
Sprint SANYO PRO-200 User Manual preview
SANYO PRO-200
Brand: Sprint Pages: 238
Alcatel OT-305A Quick Start Manual preview
OT-305A
Brand: Alcatel Pages: 2
Blu DASH 4.0 User Manual preview
DASH 4.0
Brand: Blu Pages: 54
Blu BLUJ9L Manual preview
BLUJ9L
Brand: Blu Pages: 31
Videocon v1602 User Manual preview
v1602
Brand: Videocon Pages: 28
Sagem MC 300X Owner'S Manual preview
MC 300X
Brand: Sagem Pages: 58
Samsung SM-N920S User Manual preview
SM-N920S
Brand: Samsung Pages: 153
AMGOO AM355 Manual preview
AM355
Brand: AMGOO Pages: 14
Zte 602ZT Quick Start Manual preview
602ZT
Brand: Zte Pages: 15
Zonda G10 User Manual preview
G10
Brand: Zonda Pages: 21
SoftBank 002SH Manual preview
002SH
Brand: SoftBank Pages: 24
HTC Touch Diamond DIAM500 User Manual preview
Touch Diamond DIAM500
Brand: HTC Pages: 158

Brands by name

Popular brands

Load more brands