246
GPS Function
･
To cancel the location request during positioning,
press
c
. However, the location information
may be sent depending on the timing of cancel.
Also, depending on the recipient, positioning
cannot be canceled.
･
The display items should be interpreted as follows:
: Recipient name
: Requester name*
1
: Requester ID*
2
*1 If the requester ID matches the phone number or
mail address registered in the phonebook, the
name registered in the phonebook is displayed.
While 2in1 is activated, the requester ID is
checked against the phonebook of Number A.
*2 This item may not be displayed.
INFORMATION
●
In Public mode (Driving mode), a location request is
processed as follows.
･
If you set
毎回確認
(Comfirm each time) for the usage
setting on a per-service basis, the confirmation screen
does not appear and positioning is not carried out. The
location request is added to the location log and the
icon appears on the standby display.
･
If you set
許可
(Permit) for the usage setting on a per-
service basis, the sound, vibration, and lighting used for
positioning do not operate. However, the screen is
displayed and the location information is provided.
●
Depending on signal conditions, location information that
has been sent may fail to reach the GPS service provider
or the imadoco-search searcher.
●
Location Request can be used only with Number A,
regardless of the 2in1 mode setting.
●
When the location information is requested from a caller
using the imadocokantan search, the following
operations take place.
･
A confirmation screen appears each time a location
request arrives. When you select
Yes
, a rough
positioning result is immediately notified to the
requester. After selecting
Yes
, the positioning-in-
progress screen appears and a more accurate position
is notified at the end of positioning.
･
Even if you cancel the Location Request function after
selecting
Yes
on the confirmation screen, a rough
positioning result is notified to the requester. In this
case, the request is recorded in the location log but the
location information is not displayed.
･
For details about the imadocokantan search, visit the
DoCoMo website.
Setting whether to permit or deny location requests
Request Permit/Deny
You can set whether to send the location information in
response to a location request.
1
m
z
LifeKit
z
761
z
Enter the
terminal security code
2
Set whether to permit or deny location requests
■
Permitting location requests:
1
■
Denying location requests:
2
■
Permitting location requests only for a
specified period:
3
z
Set each item
z
p
■
When the
Repeat
setting is
None
･
If you set a start time later than the current time, the
setting is enabled from the start time on this day.
･
If the start time is earlier than the current time and
the end time is later than the current time, the
setting is enabled from the current time till the end
time.
･
If the start time and the end time are both earlier
than the current time, the setting is enabled on the
next day from the start time till the end time.
･
If you set the end time as a value which is the
same as, or earlier than, the start time, the setting
is enabled until the end time of the next day.
■
When the
Repeat
setting is
Every day
or
Day of week
and the
Date
setting is
None
or
Specify start date
.
Starting this day or on the specified start date,
location requests are permitted during the period
from the start time to the end time.
Start
：
Enter the time to start the Location Request
function.
End
：
Enter the time to end the Location Request
function.
Repeat
：
Every day
: The Location Request function is
enabled everyday from the start time through
the end time.
Day of week
: Select
Day/Week
z
Highlight the
day of the week
z
o
z
p
.
Date
：
Set
Specify start date
or
Specify start/end
when
you set the period during which Location
Request is enabled.
･
This setting is required only when you set
Repeat
to
Every day
or
Day of week
.
Start
：
Enter this when you set
Date
to
Specify start
date
or
Specify start/end
.
End
：
Enter this when you set
Date
to
Specify start/
end
.
General notes regarding the permission period setting
Example
When the current time is 10:00
Example setup
Period permitted
Start time End time
11:00
18:00
11:00 to 18:00 on this day
09:00
17:00
10:00 to 17:00 on this day
06:00
09:00
6:00 to 9:00 on next day
11:00
10:00
11:00 on this day to 10:00 on next
day
09:00
08:00
10:00 on this day to 8:00 on next
day
Summary of Contents for FOMA D905I
