37
ATV [n]
Specifies whether to show the result with numeric codes or text messages.
n=0: Shows the result with numeric codes. (when parameter omitted)
n=1: Shows the result with text messages. (default)
*1, *2
ex.
Enter
ATV1
Display
None
Test
None
ATX [n]
Specifies whether to detect busy tone and dial tone, and whether to display the communication speed.
n=0: Busy tone not detected, dial tone not detected, communication speed not displayed. (when
parameter omitted)
n=1: Busy tone not detected, dial tone not detected, communication speed displayed.
n=2: Busy tone not detected, dial tone detected, communication speed displayed.
n=3: Busy tone detected, dial tone not detected, communication speed displayed.
n=4: Busy tone detected, dial tone detected, communication speed displayed. (default)
*1, *2
ex.
Enter
ATX1
Display
None
Test
None
ATZ
Resets FOMA terminal settings to those stored in the non-volatile memory with the AT&W command.
If you enter this command during receiving a packet or 64K data communication, the settings are reset
without affecting the call reception. If you enter it during communication, it disconnects the
communication first and resets the settings.
ex.
Enter
ATZ
Display
None
Test
None
ATS0= [n]
Specifies the number of ringing signals (RING) which triggers automatic call acceptance on the FOMA
terminal.
n=0: Does not accept calls automatically. (default and when parameter omitted)
n=1 to 255
*1, *2
ex.
Enter
ATS0=0
Display
ATS0?
Test
None
ATS2= [n]
Specifies an escape character.
n=0 to 127 (43: Default 0: When parameter omitted 127: To disable the escape processing)
*1
ex.
Enter
ATS2=43
Display
ATS2?
Test
None
ATS3= [13]
Specifies a carriage return (CR) character that indicates the end of AT command’s character string
(the setting is not changeable). It is attached to the end of the echoed back command string and the
result code.
*1
ex.
Enter
ATS3=13
Display
ATS3?
Test
None
ATS4= [10]
Specifies the line feed (LF) character (the setting is not changeable). It follows the CR character when
the result code is displayed with text.
*1
ex.
Enter
ATS4=10
Display
ATS4?
Test
None
ATS5= [8]
Specifies a backspace (BS) character that deletes the last character in the input buffer while you are
entering an AT command (the setting is not changeable).
*1
ex.
Enter
ATS5=8
Display
ATS5?
Test
None
ATS6= [n]
Specifies the pause period before dialing. This command sets the register but no action will occur.
n=2 to 10: 2 to 10 seconds. (5: default and when parameter omitted)
*1
ex.
Enter
ATS6=5
Display
ATS6?
Test
None
ATS8= [n]
Specifies the comma dialing function (pause time). This command sets the register but the pause time
is fixed to 3 seconds.
n=0 to 255: 0 to 255 seconds. (3: default 0: when parameter is omitted)
*1
ex.
Enter
ATS8=3
Display
ATS8?
Test
None
ATS10= [n]
Specifies the permissible delay time before automatic disconnection. This command sets the register
but no action will occur.
n=1 to 255: in 1/10 seconds. (1: default and when parameter omitted)
*1, *2
ex.
Enter
ATS10=1
Display
ATS10?
Test
None
ATS30= [n]
Specifies the time elapsed after the last data transmission to activate automatic disconnection. This
command is effective for 64K data communication.
n=1 to 255: 1 to 255 minutes.
n=0: Does not disconnect. (default and when parameter omitted)
*1
ex.
Enter
ATS30=0
Display
ATS30?
Test
None
ATS103= [n]
Specifies a mark to be used to delimit a destination sub-address if attached. This command is
effective for 64K data communication.
n=0:
＊
( when parameter omitted)
n=1: / (default)
n=2:
￥
*1
ex.
Enter
ATS103=0
Display
ATS103?
Test
None
ATS104= [n]
Specifies a mark to be used to delimit a caller sub-address if attached. This command is effective for
64K data communication.
n=0: # (when parameter omitted)
n=1: % (default)
n=2: &
*1
ex.
Enter
ATS104=0
Display
ATS104?
Test
None
AT
￥
S
Shows the command settings and the contents of the S register.
ex.
Enter
AT
￥
S
Display
None
Test
None
AT
￥
V [n]
Selects whether to use the extended result code for connection.
This command takes effect when the ATX command parameter is “n=1 to 4”.
n=0: Does not use the extended result code. (default and when parameter omitted)
n=1: Uses the extended result code.
*1, *2
ex.
Enter
AT
￥
V0
Display
None
Test
None
Command
Description & Parameter
D905i_E_Manual.fm 37 ページ ２００７年１０月１６日 火曜日 午前１１時５５分
Summary of Contents for FOMA D905I
