433
e20_dv50_7e.fm
Networ
k Se
rvice
s
J
Placing current call on hold and
answer a voice call
1
When a beeping tone is heard during
a call, press
s
.
Original call is
automatically placed on
hold and incoming call is
connected.
Press
s
to switch
between callers.
2
Press
H
when finished.
Press
s
to reconnect original call.
To end the call on hold
Press
C
and select [Disconnect].
J
Disconnecting current call and
answer a voice call
1
When a beeping tone is heard during
a call, press
H
.
Ring tone for incoming call sounds.
2
Press
s
.
Incoming call is connected.
J
Placing current call on hold and place
a separate call
1
Dial other party’s phone number
during a call.
Alternatively, select the number from
phonebook, Received calls, or Redial.
2
Press
s
.
Speak to the new party.
Original call is
automatically placed on
hold.
Press
s
to switch
between calls.
3
Press
H
when finished with the new
call.
New call is disconnected.
Press
s
to reconnect original call.
Call Forwarding Service is a service for
forwarding voice/Videophone calls to
designated phone numbers when the handset is
outside the service area or turned off, or when
calls are not answered within set ringing time.
To prioritize Call Forwarding Service when Record
message (
n
P. 74) is also set, set the ringing
time for Call Forwarding Service shorter than the
answering duration for Record message.
If a voice/Videophone call is not answered when
Call Forwarding Service is set to “Activate”, the
call is saved as “Missed call” in “Received calls”
and
B
(missed call) appears in stand-by.
Note
When a Videophone call is received during a
voice call or when a voice/Videophone call is
received during a Videophone call, in-call ring
tone is not heard and the incoming call cannot be
answered.
B
(missed call) appears when a
voice/Videophone call is ended and returned to
stand-by.
Call Forwarding Service
Using Call Forwarding
Service
Note
For
Videophone
calls, the forwarding guidance
is not played. The caller sees a message that the
call is being forwarded.
Ring tone sounds for the set ringing time (can be
changed:
n
P. 434) when Call Forwarding
Service is set to “Activate”. Answering during the
set ringing time connects call. Calls are
automatically forwarded to the set destination after
set time passes. Forwarded calls are noted in
stand-by and saved in
Received calls
. However,
calls are not saved in Received calls if ringing time
is set to [0 seconds].
Collect calls (receiver accepts charges) are not
connected when Call Forwarding Service is set to
“Activate”.
Calls received while engaged in a call can be
automatically forwarded.
Call Forwarding is automatically deactivated if
Voice Mail Service
is set to “Activate”.
Setting Call Forwarding Service from FOMA
terminal is not available from outside the service
area. In such cases, access Call Forwarding
Service from touch-tone landline phones and
payphones using
network security code
.
Remote control
must be set in advance.
When the
2in1
mode is set to [Dual mode], select
[Number A] or [Number B] to activate/deactivate
Call Forwarding Service.
dv50_e.book 433 ページ 2007年10月29日 月曜日 午前10時38分
Summary of Contents for Foma SH905i
