30
Manual for PC connection setting_DV50.fm
[M]: AT commands that can be used with the FOMA SH905i Modem Port.
AT Command List
AT Command
Overview
Parameter/Explanation
Execution
Example
AT
―
The modem function of the FOMA terminal
can be controlled by adding commands in the
list to the end of this command.
※
Returns OK if only AT is entered.
AT
o
OK
AT%V
Displays FOMA terminal
version.
*2
―
AT%V
o
Ver1.00
OK
AT&C<n>
Sets operating condition for circuit
CD (DCD) signals sent to DTE.
*1
n=0: Circuit CD always ON
n=1: Circuit CD signal changes according to
line connection status (default setting)
When “&C1” is set, the CD signal is turned
“ON” directly before the CONNECT signal is
sent when connection is completed. The CD
signal is turned “OFF” right before “NO
CARRIER” is sent when the circuit is
disconnected.
AT&C1
o
OK
AT&D<n>
Sets the operation when the
circuit ER (DTR) signal received
from DTE changes from “ON” to
“OFF” during online data mode.
*1
n=0: Ignores status (always considers signal
ON)
n=1: Sets online command mode when
signal changes from ON to OFF
n=2: Disconnects line and activates offline
mode when signal changes from ON to
OFF (default setting)
AT&D1
o
OK
AT&E<n>
Selects speed display
specifications when connecting.
*1
n=0: Wireless area transmission speed
appears.
n=1: DTE serial transmission speed appears.
(Default setting)
AT&E0
o
OK
AT&F<n>
Resets the FOMA terminal’s AT
command settings to their default
settings. If this command is
entered during communication,
the settings are reset after
disconnected.
*2
Can only be set as n=0 (can be omitted).
AT&F
o
OK
AT&S<n>
Controls when the signal of data
set ready (DR) is set to DTE.
*1
n=0: Always ON (default setting)
n=1: DR signal ON when line is connected
AT&S0
o
OK
AT&W<n>
Stores the current settings in the
FOMA terminal’s memory.
*2, 5
Can only be set as n=0 (can be omitted).
AT&W
o
OK
AT
*
DANTE
Displays the reception status of
the FOMA terminal.
*2
The result from this command is in the
following format.
*
DANTE:<m>
<m>
0:
Status where outside the service area
appears on the FOMA terminal
1:
Status where zero or one antenna
appears on the FOMA terminal
2:
Status where two antennas appears on
the FOMA terminal
3:
Status where three antennas appears on
the FOMA terminal
AT
*
DANTE
o
*
DANTE:3
OK
AT
*
DGANSM=
<n>
Sets Accept/Reject call modes for
incoming packet communications.
This setting is only valid for
incoming packet communications
after entering setup commands.
*2
n=0: Sets Reject call and Accept call settings
to [OFF] (Default setting)
n=1: Sets Reject call settings to [ON]
n=2: Sets Accept call settings to [ON]
AT
*
DGANSM=0
o
OK
AT
*
DGANSM?
o
*
DGANSM:0
OK
AT
*
DGAPL=<n>
[,<cid>]
Sets host (APN) to accept
transmissions for incoming packet
communications. APN settings
use <cid> parameter defined by
“+CGDCONT”.
*2
Adds or deletes from Accept calls list with <n>
parameter. If <cid> parameter is abbreviated,
adds (<n>=0) or deletes (<n>=1) all of <cid>
to or from list. Adds (deletes) <cid> not
defined with “+CGDCONT” to (from) list with
this command.
n=0: Adds to list (Adds APN defined by <cid>
to Accept calls list)
n=1: Deletes from list (Deletes APN defined
by <cid> from Accept calls list)
AT
*
DGAPL=0,1
o
OK
AT
*
DGAPL?
o
*
DGAPL:1
OK
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
Manual for PC connection setting_DV50.fm 30 ページ ２００７年１０月２９日 月曜日 午後１時３４分
Summary of Contents for Foma SH905i
