367
Continued on next page
A
p
p
en
d
ix/
Exter
n
al
D
evi
ces/
T
ro
u
b
lesh
o
o
ti
n
g
“Connection failed”
●
Set “Caller ID Notification” to “ON” and retry.
→
p.4
8
“Connection interrupted”
●
i-mode connection was interrupted due to poor
reception. Move to a location where the reception is
good before using the i-mode service.
→
p.46
●
If this message appears when the signal is strong and
the “
” mark is displayed, the connected site is very
busy. Retry later.
“Continue using the i-
α
ppli and communication?”
●
This is displayed when you selected “NO” or “Terminate
i-
α
ppli” in response to “The number of i-
α
ppli
communications is large. Continue communication?”
Select “YES” to continue i-
α
ppli communication. Select
“Terminate i-
α
ppli” to stop using the i-
α
ppli.
“Could not read”
●
Copying could not be completed, for some reason.
Replace with a different microSD card and try to copy
again.
“Could not start because of a different FOMA
card (UIM)”
●
This is displayed when an i-
α
ppli that is restricted by
FOMA card operational restriction attempted to start
automatically.
→
p.40
“Could not start the specified software because
of a different FOMA card (UIM)”
●
This is displayed when you specify and attempt to start
an i-
α
ppli that is restricted by FOMA card operational
restriction.
→
p.40
“Data is too long A part is deleted”
●
The size of address, subject or text or more than one
data exceeds the maximum, and the Compose
message screen appears with the excess part deleted.
“Data transmission is frequent Press CLR and
confirm data transmission”
●
This is displayed when the number of communications
from an i-
α
ppli standby screen becomes very large
within a certain period. Press
t
to select whether or
not to permit communications from the i-
α
ppli standby
display, or to close the i-
α
ppli standby display.
→
p.209
“Dial/Receive calls activating Original lock”
●
This is displayed when you have attempted a prohibited
operation while the original lock is applied to “Dial/
sending mail”.
→
p.117
“Download failed”
●
This is displayed when a download of a melody, Chara-
den or download dictionary suffered a communication
error or improper data.
(During Infrared Data Exchange/iC Exchange)
“No response Retry?”
●
The receiving terminal cannot be found/detected. If Ir
communication is used, make sure the Ir ports are
facing each other. If iC exchange is used, check the
FeliCa marks and place them together again. You can
select “YES”, then press
d
to try again.
→
pp.257, 259
“Editing now Cannot delete”
●
This is displayed if you attempt to delete a mail
message saved in the Save box while it is being edited.
“Enter correct Network Security Code”
●
This is displayed when an incorrect network security
code was input for a function which requires network
security code entry. Enter the correct network security
code.
→
p.10
8
“Error in image Does not work correctly”
●
This is displayed when a Flash movie cannot be played
due to an error found in the data.
“Error Register forwarding number”
●
This message appears when you have subscribed to
the Call Forwarding service and attempt to forward an
incoming call by selecting “Call Forwarding” from the
function menu without setting the forwarding number.
→
p.310
“External IC card not found”
●
This is displayed when the IC card authentication
function was used for user authentication, but
authentication timed out and failed.
→
p.11
8
“Failed to Copy all”
●
Copying could not be complete, for some reason.
Replace with a different microSD card and try to copy
again.
“Failed to Copy this”
●
Copying could not be completed, for some reason.
Replace with a different microSD card and try to copy
again.
“For security, the i-
α
ppli standby screen was
canceled”
“Closed due to security error”
●
This is displayed when an i-
α
ppli or i-
α
ppli standby
screen (including i-
α
ppli DX) was closed because you
attempted to perform an unauthorized operation.
→
pp.199, 209
“Format microSD for your phone”
●
There is an error such as a microSD memory card that
has not been initialized. Reformat the microSD memory
card.
→
p.251
“Input error (205)”
●
This is displayed after you input and send data from a
site of Internet homepage. Press
d
to cancel the input
text or settings (The set or input content has been sent,
so this operation does not cancel the transmission).
“Insert the FOMA card (UIM)”
●
This is displayed when the UIM is not inserted correctly,
or could be broken. Check that the FOMA card is
inserted correctly.
→
p.40
“Interrupted because maximum number of frames
exceeded”
●
The webpage cannot be displayed because the frame
count exceeds the maximum that can be displayed on
Full Browser or pixel browser.
Summary of Contents for foma SO705i
