46
B
ef
o
re
U
si
n
g
th
e H
an
d
set
Turning the FOMA Terminal
On/Off
<Power
ON/OFF>
Turning the FOMA terminal on
z
Before turning the FOMA terminal on, make sure
that the FOMA card is inserted correctly.
1
y
(1 second or longer)
After Wake-up screen appears, the standby
screen or initial settings screen appears. If you
have just attached the battery pack or you turn
the FOMA terminal back on immediately after
turning it off, “WAiT A SECOND” message may
appear for a short time.
■
When “
” appears
You are outside the FOMA
service area or in a place
where radio waves do not
reach. Move to a place where
the radio reception level icon
such as “
” appears. The
reception level is displayed
as follows:
■
If the Initial setting screen appears
→
p.47
■
If the PIN1 code/PIN2 code entry screen
appears
→
p.108
Turning the FOMA terminal off
1
y
(2 second or longer)
The shutdown screen “SO705i” appears and the
power is turned off.
Turning the FOMA terminal on/off
automatically
<Auto power ON/OFF>
Set the Auto power function, the power supply
automatically on or off at the specified time.
z
The FOMA terminal does not turn off during using
another function, even if the Auto power OFF set
time is reached. In addition, the FOMA terminal
does not turn off when the alarm notification time or
the i-
α
ppli Auto-start time is the same as the Auto
power OFF set time. The FOMA terminal turns off
after finish the function.
z
If the FOMA terminal turns off, the Music&Video
Channel program is not downloaded and reserved
update of the software is not available. Note above
when setting Auto power OFF.
<Example: Turning the FOMA terminal on
automatically>
1
i
“Settings” “Clock” “Auto
power ON”
■
Turning the FOMA terminal off
automatically
“Auto power OFF”
2
“ON” Enter the time Select wheter to
repeat or not
■
To cancel the Auto power ON/OFF
“OFF”
Switching Between Japanese
and English
<Select language>
You can switch the languages between Japanese and
English to display function names and messages on
the display.
1
i
“Settings” “Display” “Select
language” “English”
■
To change from English to Japanese
“
日本語
”
N
z
When you change the FOMA card (UIM), you have to
enter the 4 to
8
digit security code after turning on the
FOMA terminal. The standby screen appears when
the security code is successfully entered. When you
enter wrong security code for 5 times, the FOMA
terminal turns off (however, you can turn on the FOMA
terminal again).
Standby
Good
Poor
N
z
Before entering an area such as an aircraft or hospital
where there is electronic equipment that uses
extremely precise control systems or very low signal
levels and the use of mobile phones is prohibited, set
the “Auto power ON” setting to “OFF” and then turn
the FOMA terminal off.
N
z
When the FOMA card (UIM) is inserted, Select
language setting is stored on the FOMA card (UIM).
Summary of Contents for foma SO705i
