142
Security
Settings
Using the IC card authentication
<Example: To release Dial lock/Keypad lock>
1
Open the FOMA terminal when
Dial lock/Keypad lock is set
“
” appears on the screen and the user
authentication is enabled for about 10 seconds.
Pressing
p
(
) on the standby screen
also enables the user authentication.
■
To release the lock with the FOMA
terminal folded
X
Pressing
s
(LOCK) (1 second or longer)
enables the user authentication for about 10
seconds.
2
Place the contactless IC card on
the
e
mark of the FOMA
terminal
The lock is released when the user
authentication is performed successfully.
■
To use IC card authentication when the
security code is required
“
” appears when the security code entry
screen opens, and the user authentication is
enabled for about 10 seconds. Place the
registered contactless IC card on the
e
mark
of the FOMA terminal to perform the user
authentication.
Using Face Authentication
<Face authentication>
Capture your portrait and save the image name as a
keyword to be used if authentication fails for the following:
z
A dirty front camera lens may cause misoperation.
Clean with a soft cloth before capturing.
z
The rate of successful recognition may be reduced
depending on image conditions. Try the following to
improve the rate:
z
Face recognition technology does not totally
guarantee to recognize the user. Under no
circumstances shall DOCOMO be liable for any
loss or damage caused by use of this product by a
third party or lost opportunity to use this product.
1
i
X
“Settings/Service”
X
“Lock/
Security”
X
“Face authentication”
X
Enter your security code
N
z
Some contactless cards compatible with FeliCa
may not work.
z
When using the IC card authentication, hold the
contactless IC card and the FOMA terminal.
Hold the contactless IC card and the FOMA
terminal, and bring “
e
” of the back cover
close to the IC card
* Bring them close together as shown in the illustration.
Some IC cards may not be recognized properly. In
this case, wave them vertically and horizontally.
Contactless
IC card
z
If the authentication fails five times in a row, the IC
card authentication is deactivated. Perform the
authentication with the security code. After the
authentication with the security code is performed
successfully, you can use the IC card
authentication again.
• Releasing Keypad lock
• Releasing IC card lock
• Starting Reset settings
• Starting Initialize
• Starting Face
authentication
Possible cause of low
recognition rate
Solution
There is too large a contrast
between bright and dark
parts of the face if the image
is captured under strong
light or in a dark place
without sufficient light
Move to a location where
the face is evenly
illuminated.
The entire face is so
brightly illuminated so that
the image looks white
Important parts of the face
(eyes, nose, mouth or
eyebrows) cannot be
discerned because of hair,
eyeglasses or a mask
Put your hair back and
take off eyeglasses or
mask so that eyes, nose,
mouth and eyebrows are
exposed.
N
Face authentication
Function menu
¨
p.143
Summary of Contents for PRIME series N-01A
