151
Security
Settings
1
i
X
“Settings/Service”
X
“Other
settings”
X
“Reset settings”
X
Enter your security code
X
“YES”
■
When the face authentication is active
X
Face straight to the camera lens to frame the
entire face
Resetting to the Factory
Settings
<Initialize>
Delete stored data and reset the function settings to
default.
z
Pre-installed data will not be deleted.
z
Data stored/registered/set in a FOMA card (UIM) or
microSD card will not be deleted.
z
Settings configured by connecting to the network
will not be initialized.
z
Pre-installed i-
α
ppli and Widget appli that were
deleted will not be restored by “Initialize”.
z
i-
α
ppli will be deleted by “Initialize” in the following
cases:
• Pre-installed i-
α
ppli was upgraded
• Pre-installed i-
α
ppli was deleted then
downloaded
z
All data in A mode/B mode will be initialized
regardless of 2in1 mode.
z
Group names and folder names you edited are
reset to default.
z
Secret data and data in the Secret folder will be
deleted.
z
Charge the battery fully before initializing.
Initialization may not be possible if the battery is
low.
z
Do not turn off the power while initializing.
z
You cannot use other functions while initializing.
Also, you cannot receive voice, videophone or
PushTalk calls or mail.
1
i
X
“Settings/Service”
X
“Other
settings”
X
“Initialize”
X
Enter your
security code
■
When the face authentication is active
X
Face straight to the camera lens to frame the
entire face
2
“YES”
X
“YES”
Initialization starts.
Initialization may take several minutes to
complete.
After initialization is completed, the FOMA
terminal automatically reboots, and Software
Update descriptions appear.
■
If initialization did not complete
successfully
X
Select “OK” after the power is turned on
Initialization starts again.
N
z
“3G/GSM switching” may not be reset to default
depending on the network condition.
“Initialize” deletes all of your important data, history
and information (even protected data), including
phonebook entries, mail, downloaded images and
melodies, i-
α
ppli, PDF data, still images and videos
captured with the camera.
z
Performing “Initialize” resets your phone settings
to default.
It is recommended that you back up data stored
on the FOMA terminal by making notes, using
DOCOMO keitai datalink (p.447), or a microSD
card.
N
z
After you perform initialization, the ticker of
i-Channel is turned off. The ticker is turned on
automatically when the information is updated
automatically or when
u
is pressed to receive
the latest information.
z
The settings for data communications that use a
PC will not be initialized.
z
Osaifu-Keitai i-
α
ppli and the IC card data will not
be deleted.
z
After initialization, “Welcome
デコメアニメ
” (Welcome mail) and “
緊急速報「エリアメー
ル」のご案内
” (Guide to Early Warning “Area
Mail”) will be stored in Inbox.
Summary of Contents for PRIME series N-01A
