367
Data Manageme
nt
z
Note the following when you transfer Schedule
data:
• A single i-schedule data is transferred as a
normal Schedule data.
• “Send all” does not send i-schedule data.
z
Note the following when you transfer mail data:
• Some phones may be unable to receive a part of
a subject.
• “Receive all” deletes all stored mail and user
created folders then receives data.
• If there is not enough free space in Inbox when
receiving one received mail, Trash box mail and
old received mail are deleted automatically in
order. However, unread mail, protected received
mail, i-mode mail and SMS in the secret folder
are not deleted. It is recommended that you
protect important mail.
• If there is not enough free space in Outbox when
receiving one sent mail, the oldest unprotected
sent mail in Outbox is overwritten.
• When there is an attached file that has not been
completely downloaded, the mail is sent after the
attached file is deleted.
• When the i-
α
ppli activation specification or mail-
linked i-
α
ppli information is pasted into mail, the
mail is sent after the pasted data is deleted.
When a file attached to mail is restricted, the mail
is sent after the data is deleted. Also, a still
image may be deleted depending on the file
format. However, when sending sent mail or draft
mail, data received via cable connection or
copied from a microSD card are sent even when
“File restricted” is active.
• You cannot transfer the received mail folder and
sent mail folder for mail-linked i-
α
ppli. All mail in
the folder are saved to Inbox or Outbox.
• The “Color coding” setting set on the received
mail list screen or sent mail list screen cannot be
transferred.
• Mail larger than 2M bytes may not be sent
correctly via infrared data exchange.
z
When original common phrases are already stored
in all folders from Folder 3 to Folder 5, and fixed
common phrases in Folders 1 and 2 have not
changed since the time of purchase, received
common phrases will be stored in Folders 1 and 2,
overwriting the fixed common phrases.
z
Data may not be saved in the same order
depending on the model of the sender when
receiving all bookmarks.
Session number
z
“Send all” and “Receive all” require the session
number to authenticate the sender and recipient
devices. Before sending and receiving, the sender
and recipient should agree on a 4-digit number as
the session number and then both enter the same
number.
Forwarding Data via Infrared
Data Exchange
<Infrared data exchange>
When transferring data via infrared
data exchange
z
Place the devices so that the infrared data ports
are aligned on the same level and facing each
other. Also, do not place anything between the
devices or cover the infrared data ports.
z
Use the devices within 20 cm to perform infrared
communications. Do not move the devices until a
message appears indicating that transfer is complete.
z
The devices may not communicate successfully in
direct sunlight, under a fluorescent light or near
other infrared devices.
Infrared data port
Approx. 20cm
or less
Within the range
of ±15°
Summary of Contents for PRIME series N-01A
