397
Conv
enient Functions
Resetting charges automatically
<Auto reset total cost>
Configure the setting to reset the total calls cost
displayed in “Call data” to zero automatically at 0:00
on the first of every month.
1
i
X
“Settings/Service”
X
“Call
time/Charge”
X
“Auto reset total
cost”
X
Enter your security code
2
“Auto reset”
X
“ON”
X
Enter the
PIN2 code
PIN2 code
→
p.130
■
Not to set Auto reset
X
“OFF”
Setting and Notifying the
Upper Limit of Call Charges
<Notice designate calls>
If accumulated charges displayed in “Call data”
exceed the cost limit set in this function, the standby
screen or alarm notifies you.
z
The alarm notification works only once when the
accumulated charges exceed the set cost limit.
z
Exceeding the limit does not prevent you from
making calls.
1
i
X
“Settings/Service”
X
“Call
time/Charge”
X
“Notice designate
calls”
X
Enter your security code
X
Select any item:
Cost limit setting
……
Set the cost limit between 10
and 100,000 yen in 10 yen increments.
Notify setting
Notify cost limit
……
Set whether to
inform the cost limit.
Alarm tone
……
Select an alarm tone.
Volume
……
Use
c
to adjust the alarm
volume.
2
o
(Finish)
●
Alarm notification action
After ending a call, the following
actions notify you when
accumulated charges exceed the
cost limit.
■
When Notify cost limit is set
to “ON” and Alarm tone is
not set to “OFF”
When the accumulated charges exceed the preset
cost limit, the alarm tone sounds for about 5 minutes,
3 seconds after ending the call, and the notification
screen appears. To stop the alarm tone, press any
key. After the notification, pressing
t
or
y
displays the “
” (Notice designate calls) desktop
icon on the standby screen.
■
When Notify cost limit is set to “ON” and Alarm
tone is set to “OFF”
When the accumulated charges exceed the preset
cost limit, the “
” (Notice designate calls) desktop
icon appears on the standby screen.
●
Checking the content of “
(Notice
designate calls)”
Select the “
” (Notice designate calls) desktop icon
on the standby screen to check the content of Notice
designate calls.
1
On the standby screen
X
d
X
Select “
” (Notice designate
calls)
X
Enter your security code
The content of “Notice designate calls” appears.
2
Check the content
X
d
(OK)
The standby screen reappears and “
” (Notice
designate calls) disappears.
N
z
Setting Auto reset total cost to “ON” and changing
the month in “Set main time” resets the total calls
cost.
z
The Auto reset total cost is reset to “OFF” when:
• The power is turned on without a FOMA card
(UIM) inserted
•
t
is pressed on the PIN2 code entry screen
that appears when the power is turned on
• The PIN2 code is locked
→
p.130
• An error occurs on the FOMA card (UIM)
N
z
The charges for PushTalk, i-mode or packet
communication, and the Chaku-moji transmission
charges are not supported. To check i-mode
charges, see “Mobile Phone User’s Guide
[i-mode] FOMA version”.
Summary of Contents for PRIME series N-01A
