54
Befor
e
Using the Handse
t
Turning the Power On/Off
<Power ON/OFF>
Turning the power on
z
Before turning the power on, make sure that the
FOMA card (UIM) is inserted correctly.
1
y
(1 second or longer)
After the Wake-up display appears at the same
time as the Wake-up tone rings, the standby
screen or initial setting screen appears. If you
have just attached the battery pack or you turn
the power back on immediately after turning it
off, “WAIT A MINUTE” may appear for a short
time.
■
When “
” is
displayed
You are out of the service
area or in a place with no
reception. Move until the
signal strength icon such as
“
” appears. The reception
level is displayed as follows:
■
If the Initial setting screen appears
→
p.54
■
If the PIN1 code/PIN2 code entry screen
appears
→
p.130
■
Pre-stored mail
“Welcome
デコメアニメ
” (Welcome
mail) and “
緊急速報「エリアメール」のご案内
”
(Guide to Early Warning “Area Mail”) are stored
at the time of purchase.
→
p.172
Turning the power off
1
y
(2 seconds or longer)
The shutdown screen “SEE YOU” appears and
the power is turned off.
Switching between Japanese
and English
<Select language>
Switch the display language between Japanese and
English.
1
i
X
“
設定/サービス
”
X
“
ディスプ
レイ
”
X
“
バイリンガル
”
X
“English”
■
To change from English to Japanese
X
i
X
“Settings/Service”
X
“Display”
X
“Select
language”
X
“
日本語
”
Configuring Initial Settings
<Initial setting>
After turning the power on, configure initial settings in
“Set main time”, “Change security code”, “Character
size”, “Permit to send loc.”, “Keypad sound”, and
“Neuropointer” (Simple only).
1
Initial setting screen
X
“YES”
2
Set the main time
→
p.55
3
Change the security code
→
p.131
The default setting is “0000” (4 zeros).
4
Set the character size
→
p.120
N
z
The wake-up tone rings when the Wake-up
display under “Display setting” is not set to “OFF”.
z
When you change the FOMA card (UIM), you
have to enter the 4 to 8 digit security code after
turning on the power. The standby screen appears
when the security code is successfully entered. If
you enter a wrong security code 5 times, the
power turns off (you can turn on the power again).
z
If the battery ran out or the Auto power OFF
function worked to turn off the power last time, the
notification screen appears when you turn on the
power again.
Standby screen
Good
Poor
N
z
When a FOMA card (UIM) is inserted, the Select
language setting is saved to the FOMA card
(UIM).
z
When “Select language” is set to “English”, “ON”
and “OFF” will be the options for “Display” under
“Clock display” and for “Info notice setting”.
English announcement is available for some
services.
→
p.426
Initial setting
Summary of Contents for PRIME series N-01A
